Differences

This shows you the differences between two versions of the page.

--- en:lib:mdl:mdl-f-fselenco-011 [2015/10/16 14:54] – qem207
+++ en:lib:mdl:mdl-f-fselenco-011 [2024/11/14 10:50] (current) – qem103
@@ Line 1: / Line 1: @@
+^ :important:  ^ IMPORTANT: The use of these procedures could represent a risk (e.g. deletion of application), therefore it is highly recommended that they are performed by qualified experts.  ^
+The system functions are speficic procedures that allow the user to perform various operations, e.g. the configuration/calibration of peripherals, data and application save/restore on/from removable mass memory, deletion of the application and management of the mass memories.\\
+Controllers with display have some system functions that are only accessible by password and if access attempts are made the  **"Function is locked"** message is given.
+All the system functions are listed below.\\
+If the "**PWD**" column shows '**Y**', this means that the function requires a system password //(default: "123")//.\\
+DEVICE indicates an external storage media. MMC / SD or USB for hardware that they have the port.
+**System Functions**
+^n.^Led ON^System Functions^PWD^Description^
+|**1**|{{led:led_on.jpg?nolink&20}}L1|01 - Reset Error Checksum|  **-**  |Reset checksum error. \\ NOTE: if the checksum error is present, the led {{led:led_on.jpg?nolink&20}} L1 flashes.|
+|**2**|{{led:led_on.jpg?nolink&20}}L2|02 - Copy all files DEVICE -> NAND|  **-**  |Copy all files from external DEVICE to NAND Flash memory.|
+|**3**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2|03 - Copy all files NAND  -> DEVICE|  **-**  |Copy all files from NAND Flash memory to external DEVICE.|
+|**4**|{{led:led_on.jpg?nolink&20}}L3|04 - Application delete|  **Y**  |Delete the application.|
+|**5**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L3|05 - Application upload from DEVICE|  **Y**  |Upload the application from external DEVICE.|
+|**6**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3|06 - System Settings|  **-**  |Adjust the system clock and selection of the DEVICE (only for hardware that possess both ports).|
+|**7**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3|07 - Downl. retentive data to DEVICE|  **-**  |Save the retentive data on external DEVICE.|
+|**8**|{{led:led_on.jpg?nolink&20}}L4|08 - Set NEW Password|  **Y**  |Set a new password to access the "locked" system functions.|
+|**9**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L4|09 - Remove all files from NAND Flash|  **Y**  |Cancel all files stored on the NAND Flash memory.|
+|**10**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L4|10 - Show NAND Flash files|  **-**  |List the files stored on the NAND Flash memory.|
+|**11**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L4|11 - Touch Calibration|  **-**  |Run the calibration procedure of the Touch Screen, if present.|
+|**12**|{{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|12 - Set Ethernet communic. parameter|  **-**  |Run the setup procedure for the Ethernet communication parameters (IP address,..., etc.).|
+|**13**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|13 - Backup to NAND|  **-**  |Run the backup of the QCL application, data and HMI application on NAND memory.|
+|**14**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|14 - Restore from NAND|  **Y**  |Run the restore of the QCL application, data and HMI application from NAND memory.|
+|**15**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|15 - Firmware Upgrade|  **Y**  |Run the firmware upgrade from external DEVICE.\\ Available only in some hardware.|
+//Note: To exit system functions press the keep the **F1** key or **FUNC** button for at least two seconds.//