Differences

This shows you the differences between two versions of the page.

--- en:lib:mdl:mdl-f-fselenco-021 [2015/11/04 10:03] – qem207
+++ en:lib:mdl:mdl-f-fselenco-021 [2019/08/29 17:01] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
+^:important:^IMPORTANT: The use of these procedures could represent a risk (e.g. deletion of application), therefore it is highly recommended that they are performed by qualified experts.^
+The system functions are speficic procedures that allow the user to perform various operations, e.g. the configuration/calibration of peripherals, data and application save/restore on/from removable mass memory, deletion of the application and management of the mass memories.\\
+All the system functions are listed below.\\
+DEVICE indicates an external storage media. MMC / SD or USB for hardware that they have the port.
+**System Functions**
+^n.^Led ON^System Functions^Description^
+|**1**|{{led:led_on.jpg?nolink&20}}L1|01 - Reset Error Checksum|Reset checksum error. \\ NOTE: if the checksum error is present, the led {{led:led_on.jpg?nolink&20}} L1 flashes.|
+|**2**|{{led:led_on.jpg?nolink&20}}L2|02 - Copy all files DEVICE -> NAND|Copy all files from DEVICE to NAND Flash memory.|
+|**3**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2|03 - Copy all files NAND  -> DEVICE|Copy all files from NAND Flash memory to DEVICE.|
+|**4**|{{led:led_on.jpg?nolink&20}}L3|04 - Application delete|Delete the application.|
+|**5**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L3|05 - Application upload from DEVICE|Upload the application from DEVICE.|
+|**6**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3|06 - System Settings|**//Not implemented for this hardware//**|
+|**7**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3|07 - Downl. retentive data to DEVICE|Save the retentive data on DEVICE.|
+|**8**|{{led:led_on.jpg?nolink&20}}L4|08 - Set NEW Password|**//Not implemented for this hardware//**|
+|**9**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L4|09 - Remove all files from NAND Flash|Cancel all files stored on the NAND Flash memory.|
+|**10**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L4|10 - Show NAND Flash files|**//Not implemented for this hardware//**|
+|**11**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L4|11 - Touch Calibration|**//Not implemented for this hardware//**|
+|**12**|{{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|12 - Set Ethernet communic. parameter|**//Not implemented for this hardware//**|
+|**13**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|13 - Backup to NAND|Run the backup of the QCL application, data and HMI application on NAND memory.|
+|**14**|{{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|14 - Restore from NAND|Run the restore of the QCL application, data and HMI application from NAND memory.|
+|**15**|{{led:led_on.jpg?nolink&20}}L1\\ {{led:led_on.jpg?nolink&20}}L2\\ {{led:led_on.jpg?nolink&20}}L3\\ {{led:led_on.jpg?nolink&20}}L4|15 - Firmware Upgrade|Run the firmware upgrade from DEVICE.\\ Available only in some hardware.|
+//Note: To exit system functions press the keep the **FUNC** button for at least two seconds.//