en:lib:mdl:mdl-h-mccabla-010

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
en:lib:mdl:mdl-h-mccabla-010 [2016/09/21 17:39] – [32.1. Cabling] qem103en:lib:mdl:mdl-h-mccabla-010 [2019/10/31 16:05] (current) – [End cap crimping tool] qem103
Line 1: Line 1:
  
 +===== - Cabling =====
 +
 +^:important:^ • Please read carefully.\\ • See technical notes on Weidmuller terminals BLZF, BLZ and B2L.^
 +
 +==== Types of Connectors ====
 +^ ^Family^Wire Section\\ no end caps^Wire section\\ with end caps^Characteristics\\ of contact^Tools^
 +|  {{connettori:connettore_fila-singola_01.png?nolink&80}}  |BLZF 3.5|0.3-1.50 mm<sup>2</sup>|0.3-1 mm<sup>2</sup>|  {{icone:icona_cnn-molla.png?nolink&80|Contatto a molla autobloccante}}  |Open the self-locking, spring clip terminals with a flat blade screwdriver to DIN 5264-A as shown below\\ \\ See the table below for recommended cap ends \\ \\ To crimp the cap ends to the wire use the tool below|
 +|  {{connettori:connettore_fila-doppia_01.png?nolink&80}}  |B2L 3.5|0.3-1.00 mm<sup>2</sup>|0,3-0.5 mm<sup>2</sup>|:::|:::|
 +|  {{connettori:connettore_fila-singola_02.png?nolink&80}}  |BLZF 5.08|0.3-2.50 mm<sup>2</sup>|0.3-2.00 mm<sup>2</sup>|:::|:::|
 +|  {{connettori:connettore_fila-singola_03.png?nolink&80}}  |BLZ 5.00|0.2-2.50 mm<sup>2</sup>|0.1-1 mm<sup>2</sup>|  {{icone:icona_cnn-vite.png?nolink&80|Screw contact}}  |The screw terminals can be tightened with a flat blade screwdriver to DIN 5264 as shown in fig.4.7\\ Tightening torque: 0.4 - 0.5 Nm.|
 +
 +**For a safer cabling, always use wire end caps**
 +
 +====Tools====
 +===End caps===
 +^Wire section^End cap section^Make^Model^
 +|0.1-0.3 mm<sup>2</sup>|0.95 mm<sup>2</sup>|Cembre|PKE 308|
 +|0.3-0.5 mm<sup>2</sup>|1.32 mm<sup>2</sup>|Cembre|PKE 508|
 +|:::|:::|BM|BM00601|
 +|1 mm<sup>2</sup>|2.5mm<sup>2</sup>|BM00603|PK 108|
 +|:::|:::|BM|BM00603|
 +
 +=== End cap crimping tool ===
 +
 +<WRAP center round info 60%>
 +{{varie:pinza_cembre.png?nolink&300  }}Use a crimp tool type “Cembre ND#4
 +cod. 2590086”
 +</WRAP>
 +
 +===Screwdrivers===
 +<WRAP column 30%>
 +{{varie:cacciavite_01.png?nolink&200}}
 +Screwdriver for opening self-locking spring clip terminals:\\
 +A = 0.6mm\\
 +B = 2.5mm max\\
 +C = 7 mm min\\
 +</WRAP>
 +<WRAP column 30%>
 +{{varie:cacciavite_02.png?nolink&200  }}
 +Screwdriver for tightening screw terminals:\\
 +A = 0.6mm\\
 +B = 3.5mm\\
 +</WRAP>
 +
 +
 +====Procedure====
 +<WRAP col2>
 +{{varie:puntalini_01.png?nolink&200}}\\
 +Strip 10mm of copper wire
 +</WRAP>
 +
 +<WRAP col2>
 +{{varie:puntalini_02.png?nolink&200}}\\
 +Fit the end cap and crimp it with a crimping tool
 +</WRAP>
 +
 +<WRAP col2>
 +{{varie:puntalini_03.png?nolink&200}}\\
 +a) fit the screwdriver without turning it\\
 +b) fit the cable in the terminal
 +</WRAP>
 +
 +<WRAP col2>
 +{{varie:puntalini_04.png?nolink&200}}\\
 +Remove the screwdriver
 +</WRAP>