en:strumenti:accessori:qbr1a:mimqbr1axx

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
en:strumenti:accessori:qbr1a:mimqbr1axx [2016/09/16 17:16] – [7.4. Indicazioni per gli amministratori di rete] qem103en:strumenti:accessori:qbr1a:mimqbr1axx [2019/08/29 17:01] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +====== QBR1A ======
 +{{:varie:timbro_preliminare_30g.png?nolink&200  }}
  
 +{{  strumenti:accessori:qbr1a:bridge_3d_01.png?direct&400  |QBR1A}}
 +
 +<html><pagebreak /></html>
 +
 +====== - Informations ======
 +
 +===== - Release =====
 +
 +^ Document release ^ Description ^ Note ^ Date ^
 +|  01  | New manual | Valid for hardware release 01  |20/06/2012|
 +
 +{{page>en:lib:mdl:mdl-h-cemarce-010}}
 +
 +<html><pagebreak /></html>
 +
 +====== - Description ======
 +
 +**QBR1A** is a LAN/GPRS router produced for the Teleassistance of QEM products.\\
 +It can be equipped with:
 +
 +^  Standard equipment  ||
 +|{{Icone:Icona_led.png?nolink&50}}|8 system leds|
 +|{{Icone:Icona_prog.png?nolink&50}}|1 serial (RS232/TTL) COM1 (Use in combination with the accessory [[en:Strumenti:Accessori:IQ009]])|
 +|{{Icone:Icona_seriale.png?nolink&50}}|1 multistandard serial (RS232/422/485) - COM2|
 +|{{Icone:Icona_ethernet.png?nolink&50}}|1 ETHERNET port |
 +|{{Icone:Icona_mmc.png?nolink&50}}|1 Memory Card MMC/SD reader|
 +|{{Icone:Icona_orologio.jpg?nolink&50}}|Clock calendar|
 +|{{Icone:Icona_digital-in.png?nolink&50}}|2 standard digital inputs|
 +|{{Icone:Icona_digital-out.png?nolink&50}}|2 digital outputs|
 +^  Optional equipment (Refer to the table [[#Hardware versions]])  ||
 +|{{Icone:Icona_seriale.png?nolink&50}}|1 multistandard serial (RS232/422/485) – COM3 PORT|
 +|{{Icone:Icona_canbus.png?nolink&50}}|1 CANbus port|
 +|{{Icone:Icona_digital-in.png?nolink&50}}|8 standard digital inputs|
 +|{{Icone:Icona_digital-out.png?nolink&50}}|8 digital outputs|
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +===== - Product Identification =====
 +
 +^:tip:^The Ordering Code provides the exact product features.\\ Make sure that the product features meet your requirements.^
 +
 +==== - Product Label ====
 +
 +{{strumenti:accessori:qbr1a:qbr1a_etichetta-prodotto_01.png?nolink&400|}}
 +
 +{{page>en:lib:mdl:mdl-h-mclegeti-010}}
 +
 +==== - Hardware versions ====
 +
 +There are currently 2 hardware versions:
 +
 +|**Ordering code**|**Features**|**Part Number**|
 +^QBR1A01E0/0/24V          |Router LAN  |  94020001  |
 +^QBR1A01E0/GPRS/24V       |Router LAN/GPRS  |  94020002  |
 +
 +<html><pagebreak /></html>
 +
 +===== - Product Configuration =====
 +
 +{{:strumenti:accessori:qbr1a:qbr1a_conformazione_01.png?nolink&300}}
 +
 +  * **a** = GPRS antenna
 +  * **b** = connections side
 +  * **c** = settings side
 +  * **d** = power supply and I/O connectors
 +  * **e** = connection for Omega DIN
 +
 +==== - Firmware versions ====
 +
 +^Version^Description^
 +|  01  |Connection with QNet, with GPRS and LAN modem|
 +
 +<html><pagebreak /></html>
 +
 +====== - Electrical features ======
 +
 +===== - General features =====
 +
 +^Weight (maximum hardware configuration)|FIXME|
 +^Box material|FIXME|
 +^Signal leds|8|
 +^System keyboards|24|
 +^Working temperature|0 ÷ 50°C|
 +^Relative humidity|90% without condensation|
 +^Altitude|0 - 2000m s.l.m.|
 +^Transport and storage temperature|-25 ÷ +70   °C|
 +^IP protection|IP20|
 +
 +===== - CPU (F level technology) =====
 +
 +^RISC microprocessor (32 bit)^^
 +^Work frequency|  200MHz|
 +^RAM|  16MB|
 +^Flash|  8MB|
 +
 +
 +===== - Dimensions =====
 +
 +^:info:^Lengths in mm^
 +
 +
 +{{strumenti:accessori:qbr1a:qbr1a_dimensioni_01.png?nolink&500}}
 +
 +<html><pagebreak /></html>
 +
 +====== - Electrica features and connections ======
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_front_01.png?direct&600  }}
 +
 +<html><pagebreak /></html>
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_sx_01.png?direct&400  }}
 +
 +<html><pagebreak /></html>
 +
 +===== - Power supply =====
 +
 +^:important:^ • The wiring must be installed by skilled personnel and with appropriate antistatic measures.\\ • Before handling the tool, disconnect the power supply and all the parts connected to it.\\ • To ensure compliance with EC regulations, the power supply must have a galvanic insulation of at least 1500 Vac.^
 +
 +
 +^Power supplies available^  24 Vdc  ^
 +^Range|  22 ÷ 27 Vdc  |
 +^Max. absorption|  FIXME DISTINGUERE I 2 MODELLI |
 +
 +^  CN1  ^Terminal^Symbol^Description^
 +|{{  connettori:cnn_3fv_p5_22020219.png?nolink&70  }}|  1  |  **+**  |DC positive power supply|
 +|:::|  2  |  TERRA  |Ground-PE (signals)|
 +|:::|  3  |  **-**  |DC 0V power supply|
 +
 +<html><pagebreak /></html>
 +
 +===== - COM1 PORT (USB mini-B) =====
 +
 +^COM1 PORT^Description^
 +|  {{connettori:cnn_5f_usbmini-b_01.png?nolink}}  |COM1 serial port TTL standard electric used for connection to a QMove+ product (DIP 8 of SW1 OFF) or to the PC for the Bridge configuration (DIP 8 of SW1 ON).\\ In the latter case, you must use the IQ009 or IQ013 accessories.|
 +
 +===== - COM2 PORT (multistandard) =====
 +==== - Connettore COM2 PORT ====
 +^  CN2  ^Morsetto^RS232^RS422^RS485^Descrizione^
 +|{{connettori:cnn_6x2fv_p3.5_01.png?nolink&100}}|  1A  |  -  |  -  |  A  |Terminale A - RS485|
 +|:::|  2A  |  -  |  -  |  B  |Terminale B - RS485|
 +|:::|  3A  |  0V  |  0V  |  0V  |Comune COM2 PORT|
 +|:::|  4A  |  0V  |  0V  |  0V  |Comune COM2 PORT|
 +|:::|  5A  |  TX  |  -  |  -  |Terminale TX - RS232|
 +|:::|  6A  |  Terra  ||||
 +|:::|  1B  |  -  |  RX  |  -  |Terminale RX - RS422|
 +|:::|  2B  |  -  |  RXN  |  -  |Terminale RX N - RS422|
 +|:::|  3B  |  -  |  TX  |  -  |Terminale TX - RS422|
 +|:::|  4B  |  -  |  TXN  |  -  |Terminale TX N - RS422|
 +|:::|  5B  |  RX  |  -  |  -  |Terminale RX - RS232|
 +|:::|  6B  |  Terra  ||||
 +
 +==== - COM2 PORT standard settings ====
 +
 +^  SW2  ^Num.\\ Dip^Name\\ DIP^Setting\\ of the DIP^^^Function^
 +|{{dip-switch:dip-6.png?nolink&100}}|  1  |  JP2  |  ON  |  X[(X = not significant setting)]  |  X[(#1)]  |Termination [[#RS485]]|
 +|:::|  2  |  JP3  |  ON  |  X[(#1)]  |  X[(#1)]  |Polarization [[#RS485]]|
 +|:::|  3  |  JP1  |  ON  |  X[(#1)]  |  X[(#1)]  |:::|
 +|:::|  4  |    |  OFF  |  ON  |  OFF  |COM2 PORT standard settings selection|
 +|:::|  5  |    |  ON  |  OFF  |  OFF  |:::|
 +|:::|  6  |    |  OFF  |  OFF  |  ON  |:::|
 +|:::|    |    |  **RS485**  |  **RS422**  |  **RS232**  | |
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +===== - ETHERNET PORT =====
 +
 +^ETHERNET PORT^Description^
 +|  {{connettori:cnn_ethernet_01.png?nolink&70}}  |RJ45 connector.\\ \\ LED:\\  * LINK: green led = cable connected\\  * DATA: yellow led = data exchange (the flashing led indicates data communication between connected devices)|
 +
 +===== - MMC/SD =====
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_mmc_01.png?direct&500  }} Memory card slot (highlighted by the arrow)
 +
 +<html><pagebreak /></html>
 +
 +===== - SIM CARD =====
 +
 +{{ :strumenti:accessori:qbr1a:qbr1a_sim_01.png?300&direct  }}
 +
 +Slot for SIM card (highlighted by the arrow)
 +
 +<html><pagebreak /></html>
 +
 +===== - 2 standard digital inputs and 2 standard digital outputs =====
 +
 +^:tip:^The electrical features are given in paragraph [[#Electrical features]].\\ The connection examples are provided in paragraph [[#Connection examples]]^
 +
 +^  CN3  ^Terminal^Symbol^Description^
 +|  \\  {{connettori:cnn_6fv_p3.5_02.png?nolink&80}}  |  1  |  I1  |Input I1|
 +|:::|  2  |  I2  |Input I2|
 +|:::|  3  |  PL  |Common of the digital inputs|
 +|:::|  4  |  O1  |Outputs O1|
 +|:::|  5  |  O2  |Outputs O2|
 +|:::|  6  |  COM  |Common of the digital outputs|
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +====== - Connection examples ======
 +
 +===== - Connection between QBR1A (COM2) and the Qmove (C1, J1) Prog port =====
 +
 +|[[Strumenti:Qmove:C1|Qmove compatto (C1)]], [[Strumenti:Qmove:J1|Qmove integrato (J1)]]  | |  [[en:strumenti:accessori:qbr1a|QBR1A]]|
 +|{{ :cavi:cavo_vasc-rs232-weid-b2l2x6_01.png?direct&700 }}|||
 +|DSUB 9P-M\\ 22010025  | |  WEIDMULLER B2L 3.5/12\\ 22020159|
 +
 +
 +<WRAP left round important 40%>
 +**Set the [[#COM2 PORT standard settings|dip switch SW2]] as in table:**\\
 +^  SW2  ^Num.\\ Dip^Setting\\ of the DIP^
 +|{{dip-switch:dip-6.png?nolink&100}}|  1  |  OFF  |
 +|:::|  2  |  OFF  |
 +|:::|  3  |  OFF  |
 +|:::|  4  |  OFF  |
 +|:::|  5  |  OFF  |
 +|:::|  6  |  ON  |
 +</WRAP>
 +
 +
 +<html><pagebreak /></html>
 +
 +===== - Connection between the PC and the QBR1A (LAN) =====
 +
 +Is it necessary to use a **direct ethernet cable** as per specification EIA/TIA-568B-568B.
 +
 +{{:connettori:cnn_rj-45_tia-568b_left.png?direct&300|}}  {{:connettori:cnn_rj-45_tia-568b_right.png?direct&300|}}
 +
 +===== - Connection between the QBR1A (LAN) and the QMove (LAN) =====
 +
 +It is necessary to use an **ethernet crossover cable** specification EIA/TIA-568B-568A .
 +
 +{{:connettori:cnn_rj-45_tia-568b_left.png?direct&300|}}  {{:connettori:cnn_rj-45_tia-568a_right.png?direct&300|}}
 +
 +<html><pagebreak /></html>
 +
 +====== - Settings, procedures and signals ======
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_settaggi_01.png?direct&500  |Reae view for finding devices described in this chapter.}} 
 +
 +<html><pagebreak /></html>
 +
 +===== - SW1 selector =====
 +
 +^  SW1  ^Dip^Name^Function^
 +|  {{dip-switch:dip-8.jpg?direct&100}}  |  1  |  |n.u.  |
 +|:::|  2  |  |n.u.  |
 +|:::|  3  |  |n.u.  |
 +|:::|  4  |  |n.u.  |
 +|:::|  5  |  AUTOUPDATE  |**ON** = When you connect to the QNet network, checks for a new firmware and then download and upgrade. At the end system performs a Reboot. See section [[#Upgrade Firmware]]|
 +|:::|  6  |  DIAGNOSTICS  |**ON** = Displays antenna signal strength in leds L1-L4 (see the section FIXME )|
 +|:::|  7  |  |n.u.  |
 +|:::|  8  |  RESOURCE\\  \\  CONFIGURATION  |**OFF** = Select the COM1 (mini-USB) for communication with a QMove using the cable supplied with the accessories [[en:strumenti:accessori:iq009|IQ009]] or [[en:strumenti:accessori:iq013|IQ013]].\\  **ON** = Put the Bridge in Configuration mode, select the COM1 (mini-USB) for communication with a QMove using the cable supplied with the accessories [[en:strumenti:accessori:iq009|IQ009]] or [[en:strumenti:accessori:iq013|IQ013]]. \\ **!!! WARNING !!!** \\ //You must have special attention to the correct connection because the two different modes of operation reverse signals RX/TX then you could damage the electronic components.//|
 +
 +**Default: only dips 5 and 6 ON**
 +
 +FIXME Verificare l'immagine del dip-switch: ON e OFF sono rovesci.
 +
 +<html><pagebreak /></html>
 +
 +===== - Led =====
 +
 +The **"PWR, RUN, DATA, ERR"** leds are the system leds while the **"L1, L2, L3 **and** L4"** leds are used to display different data depending on conditions/application settings.
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_led_01.png?250  }}
 +
 +
 +==== - Alerts ====
 +=== - Leds meaning ===
 +
 +{{led:led_on.jpg?direct&30}} Led ON
 +
 +{{led:led_off.jpg?direct&30}} Led OFF
 +
 +{{led:led_lamp.jpg?direct&30}} Led flashing
 +
 +^Led^Color^State^Description^
 +|**PWR**|Green|{{led:led_on.jpg?20}}|Bridge operative and communication module initialized.  |
 +|:::|:::|{{led:led_lamp.jpg?20}}|If this is the only lampegiante, led shows the status of communication module initialization. If **DATA** led flashing, reports that the Bridge is in edit mode **Configurazione/Configuration Mode**.  |
 +|**RUN**|Green|{{led:led_off.jpg?20}}|Bridge waiting**Enabling the connection**.  |
 +|:::|:::|{{led:led_lamp.jpg?20}}|Short blinking = Bridge waiting **Activation command connection**.\\  Slow blinking = Bridge to connect/disconnect to/from network QNet.  |
 +|:::|:::|{{led:led_on.jpg?20}}|Bridge connected to the network QNet.  |
 +|**DATA**|Yellow|{{led:led_on.jpg?20}}|If the **PWR** led is on, report the arrival the network information by QNet.\\ If the **PWR** led flashing, report that the bridge is in **Configurazione/Configuration Mode**.  |
 +|**ERR**|Rosso|{{led:led_lamp.jpg?20}}|If all other leds are in OFF, report an hardware error. See the section [[#Hardware error codes]].\\ If the **PWR** led is flashing, report an error during the initialization phase of the communication module. In the case of GPRS modem make sure you have inserted the SIM card and the PIN code.\\ If the **RUN** led is flashing, report an error during the QNet network connection. In the case of the GPRS modem make sure you have signal (see the section [[#Antenna signal strength]]).\\ You can view a description of the error message by using the utility [[en:software:qworkbench:utility:qrm:BridgeConfigurator]].|
 +
 +
 +=== - Hardware error codes ===
 +
 +If a malfunction is detected when power on of any devices, the system hangs and the error is reported by the blinking of the led only {{led:led_lamp.jpg?direct&20}}ERR while all the other leds remain in OFF.
 +
 +The flashing numbers indicates the error type as to the following table:
 +
 +^Flashing numbers^Error^
 +|  1  |Exception|
 +|  2  |FPGA|
 +|  3  |Media|
 +|  4  |Bootloader|
 +|  5  |Firmware|
 +|  6  |Resource|
 +|  7  |Modem|
 +|  8  |Memory write|
 +
 +^:important:^Each of these reports indicates a serious error. The product must be sent to customer support QEM.^
 +
 +
 +=== - Antenna signal strength ===
 +
 +If you have a Bridge with GPRS modem antenna signal strength value (RSSI) you receive through the flashing of leds L1, L2, L3, L4.
 +
 +^L1^L2^L3^L4^Description^
 +|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|No signal (-113 dBm o meno) o scarso |
 +|{{led:led_lamp.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|-111 dBm < RSSI < -77 dBm\\  Insufficient signal  |
 +|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|-77 dBm < RSSI > -69 dBm\\  Sufficient signal  |
 +|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|{{led:led_off.jpg?direct&15}}|-69 dBm < RSSI > -63 dBm\\  Good signal  |
 +|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|{{led:led_lamp.jpg?direct&15}}|RSSI > -63 dBm\\  Optimal signal\\  <WRAP left round important 80%>  **In some cases, employees by the operator, this message appears even when no signal.**  </WRAP>  |
 +
 +<html><pagebreak /></html>
 +
 +===== - Keys =====
 +
 +{{  strumenti:accessori:qbr1a:qbr1a_pulsanti_01.png?direct&400  }}
 +
 +FIXME - Nel Bridge il RESET è all'esterno, quindi BOOT e FUNC.
 +
 +^Name  ^Description^
 +|{{varie:pulsante_6x6.jpg?40}}FUNC  |If the condition of __//Enable the connection//__ satisfied, pressed for at least 1 second to activate the QNet network connection (the **RUN** led flashes).|
 +|{{varie:pulsante_6x6.jpg?40}}BOOT  |Pressed at power ON, set the instrument in Boot state, allowing access to firmware update.|
 +|{{varie:pulsante_6x6.jpg?40}}RESET  |The system gets restarted.|
 +
 +
 +
 +<html><pagebreak /></html>
 +
 +====== - The QNet network ======
 +
 +The QNet network  provides the structure for connecting two or more QRM nodes (Qem Resource Manager) through the Internet network.
 +
 +{{strumenti:accessori:qbr1a:qnet01.png?600 |}}
 +
 +
 +===== - The QRC server =====
 +
 +The QRC (Qem Resources Control) server, is a server QEM that manages the connection permissions between the various network QNet nodes.
 +
 +
 +===== - The QRM-QRMB =====
 +
 +The QRM (Qem Resource Manager) or the QRMB (Qem Resource Manager for Bridge) are the Nodes that share, using the resources, the means to access more tools Qem.
 +
 +===== - The network QNet resources =====
 +
 +Are considered **resources** all //communication channels// provided by various nodes QRM-QRMB to connect the different QMove systems.
 +
 +
 +===== - Directions for network administrators =====
 +
 +The connection to the QNet network using an encrypted protocol. \\
 +On a LAN network, therefore every Bridge will open a connection TCP/IP OUT on the gate **8005** way the server QEM QRC at the address **qrc.q-move.eu** (188.95.77.82).
 +To enable the auto-update the firmware it is also necessary that the Bridge can take advantage of the FTP Protocol (gate TCP/IP 20-21) always log on to the server at the address in QEM QRC **qrc.q-move.eu** (188.95.77.82).
 +To enhance safety on the LAN every other type of communication can be blocked.
 +
 +<html><pagebreak /></html>
 +
 +====== - General information of operation ======
 +
 +===== - Introduction =====
 +
 +This chapter will introduce some concepts and describes some product operations. These contents are partly related and implemented in the firmware.
 +
 +===== - The Bridge resources =====
 +
 +Are considered **resources** all the //comunication channels// provided by the Bridge to connect more QMove systems. The **channel** word will be synonymous with **resource**.\\
 +All serial port (COM) on the Bridge are resources. In the base versione there are two serials: COM1 and COM2. With the expansion is available the serial: COM3.\\
 +In the case of presence of the Ethernet port, 3 channels of communication are generated: LAN1, LAN2, LAN3.\\
 +
 +In the maximum configuration, the Bridge can have 6 channels of communication, that can be connected to a QMove system.
 +
 +===== - The Manager channel =====
 +
 +Is there a particular communication channel, used exclusively by the QNet network called **Manager**.\\
 +It safeguard all communication to the **QRMB**.
 +
 +===== - Conditions and Enables =====
 +
 +To ensure that the Bridge run is the status of the connection if desired **Enable the connection**.\\
 +By default, the condition is satisfied as long as the **I1 input** is active.
 +When the condition //Enable the connection// is satisfied, for default, the **O1 output** is active.
 +===== - Operating States =====
 +
 +This section describes the operating States.
 +
 +==== - Boot ====
 +
 +The **Boot** phase, is the first to be performed after switching on (or the reset) of the instrument.\\  
 +During this phase runs a scan of all leds.\\  
 +If an hardware failure is detected, the system hangs and only **ERR** led flashes indicating the type of error (see the section [[#Hardware error codes]]).
 +
 +==== - Recognition and Hardware configuration ====
 +
 +The Bridge check that all devices are operational.\\ 
 +The phase is signalled by the blinking of the **PWR** led only.\\ 
 +In case of error the **ERR** led starts blinking.\\  \\ 
 +One of the possible errors, in the presence of the **Modem 3G** module, is the non-inclusion of the [[#SIM CARD]] or the PIN error (parameter //gprs1_pin//).
 +
 +==== - Connection request waiting ====
 +
 +The Bridge is waiting to connect to the network QNet network.\\ 
 +The **PWR** led is steadily lit.\\ 
 +The **RUN** led, if in OFF, indicates that the conditions of qualification for the connection isn't verified.\\ 
 +When the enable conditions are met, the **RUN** led start flashes briefly and the **O1 output** is active.
 +
 +==== - Connection to a QNet network ====
 +
 +The Bridge is connecting to the QNet network.\\ 
 +The **PWR** led is in ON and steadily lit and the **RUN** led is flashing continuously.\\ \\ 
 +
 +==== - Firmware Upgrade ====
 +
 +If the SW1 dip n°5 (AUTOUPDATE) is ON, before connecting to the QNet network, the Bridge check if a firmware update.\\ 
 +If it discovers an new firmware, it gets downloaded.\\ 
 +This stage is marked by a continuous flashing of L1, L2, L3 e L4 leds. \\ 
 +
 +^:important:^ • At the end of the download the Bridge goes in the **BOOT** state to store in the flash the new firmware.\\ • **DO NOT TURN OFF** the Bridge.^
 +
 +**Finished updating, the Bridge will automatically reboot.**
 +==== - Error ====
 +
 +The error message occurs with the **ERR** led.\\ 
 +The Bridge, in some cases, attempts to do so failed.
 +
 +===== - Configuration =====
 +
 +==== - Bridge System Info ====
 +
 +The following lists contain information parameters of Bridge, //Bridge System Info//, that can be read by the application [[#Utility QRM BridgeConfigurator]].
 +
 +^Name^Type^Default^Description^
 +|**Firmware**  ||||
 +|name|stringa|QBR1A  |Nome del firmware in uso.  |
 +|version|string|1.0.1  |Current firmware version.  |
 +|serial number|entire|12345678  |Serial Number of the connected Bridge.  |
 +|checksum|string|12345678  |Checksum of the used firmware.  |
 +|  ||||
 +|**Timedate**  ||||
 +|date|date|20120131  |Data used, in the form **YYYMMDD**.\\ //Example, 20120131, 31 gennaio 2012//  |
 +|time|time|165513  |Time used, in the form **hhmmss**.\\ //Example, 165513, 16.55.13//  |
 +|  ||||
 +|**Module data: LAN**  ||||
 +|Device LAN|string|2  |Indicates that the connection to the server QRC is: LAN  |
 +|manufacture|string|  |Producer  |
 +|model|string|  |Model  |
 +|mac|string|  |MAC address  |
 +|dhcp|entire|0  |DHCP Type  |
 +|ip address|ip|192.168.0.253  |IP address  |
 +|netmask|ip|255.255.255.0  |Netmask  |
 +|gateway|ip|0.0.0.0  |Gateway address  |
 +|  ||||
 +|**Module data: modem 3G**  ||||
 +|Device 3G|string|2  |Indicates that the connection to the server QRC is: LAN  |
 +|manufacture|string|  |Producer  |
 +|model|string|  |Model  |
 +|fw|string|  |Firmware version  |
 +|imei|string|  |IMEI code  |
 +|iccid|string|  |ICCID code  |
 +|imsi|string|  |IMSI code  |
 +|  ||||
 +|**Features**  ||||
 +|mtu_qrm|entire|  |Specifies the MTU value of the QRMB server  |
 +|mtu_bridge|entire|  |Specifies the MTU value of the Bridge  |
 +|channels_com|entire|2  |Specifies the available COM channels  |
 +|channels_tcp|entire|0  |Specifies the available TPC channels  |
 +
 +
 +==== - Bridge System Settings ====
 +
 +Lists the configuration parameters of the Bridge, //Bridge System Settings//, that can be modified by the application [[#QRM BridgeConfigurator Utility]].
 +
 +^Name^Type^Default^Description^
 +|**Section QRM-Bridge**  ||||
 +|qrc_ip|string|188.95.77.82\\  qrc.q-move.eu  |IP Address/Hostname of the QRMB server that the Bridge connects.  |
 +|qrc_port|number|8005  |QRMB server TCP port number to which the Bridge connects.  |
 +|  ||||
 +|**Section FTP**  ||||
 +|ftp_ip|string|188.95.77.82\\  qrc.q-move.eu  |IP Address/Hostname of the FTP server athat the Bridge connects for firmware update. |
 +|ftp_port|number|21  |FTP server TCP port number  |
 +|ftp_user|string|  |User name for FTP server authentication.\\  If empty, it is automatically generated by the Bridge.  |
 +|ftp_pass|string|  |User password for authentication to the FTP server.\\  If empty, it is automatically generated by the Bridge.  |
 +|  ||||
 +|**Section ETH** (valid only with network interface)  ||||
 +|eth0_mac  |string  |00:00:00:00:00:00  |MAC address of Bridge network interface (if present).  |
 +|eth0_dhcp  |number  |0  |Type of DHCP Client setting:\\  0 = disable  |
 +|eth0_dhcpip  |string  |0.0.0.0  |IP Address/DHCP Hostname server .\\ //(currently not supported)//  |
 +|eth0_ip  |string  |192.168.0.253  |IP Bridge address.  |
 +|eth0_nm  |string  |255.255.255.0  |Network mask.  |
 +|eth0_gw  |string  |192.168.0.1  |IP gateway address.  |
 +|eth0_dns1  |string  |0.0.0.0  |DNS1 IP Address.\\ //(currently not supported)//  |
 +|eth0_dns2  |string  |0.0.0.0  |DNS IP Address.\\ //(currently not supported)//  |
 +|  ||||
 +|**GPRS Modem section** (valid with the modem)  ||||
 +|gprs1_pdp  |string  |ibox.tim.it  |GPRS context.  |
 +|gprs1_pin|number|  |PIN code of the SIM  (normally empty or 0000).  |
 +|  ||||
 +|module_pref  |number  |0  |**Default module**:\\ With the Bridge who have both Ethernet interface and GPRS, indicates the module that is used when connecting to the QRC.\\ 0 = LAN\\ 1 = GPRS |
 +|  ||||
 +|**Additional functionality**  ||||
 +|fn_autoconnect  |number  |1  |**Auto-login**:\\  0 = Disable (default)\\  1 = At the power ON of the Bridge the connection operations are enabled (simulates I1 on).\\  2 = At the power ON of the Bridge is immediately connected to the QNet network, if the ratings are valid (simulates I2 on).\\  3 = At the power ON of the Bridgee is immediately connected to the QNet network (simulates I1 and I2 on).  |
 +|fn_i01  |number  |0  |**Input 1 function**:\\  0 = Abilitazione alla connessione (default).\\  Stato: Continuo.\\  Con l'ingresso alto, vengono abilitate le operazioni di connessione.\\  Con l'ingresso basso, vengono chiuse eventuali connessioni in essere ed inibite le successive (anche WAKE-UP).  |
 +|fn_i02  |number  |0  |**Input 2 function**:\\  0 = Enable/Disable connection (default).\\  State: Impulsive. Minimum duration of command: 1 sec.\\  The activation of the input will cause the network connect/disconnect procedure to the QNet network.\\  If FunctionI1 is 0, the input issubject to the consent of I1 (active).  |
 +|fn_o01  |number  |0  |**Output 1 function**:\\  0 = Ready connect (default).\\  Output OFF: if I1 is OFF or the start up conditions are not valid.\\  Steady output: if I1 is in ON and if all start up conditions are valid (SIM ok, network presence, etc...).  |
 +|fn_o02  |number  |0  |**Output 2 function**:\\  0 = Connection state (default).\\  Output OFF: Connection is not present or in progress.\\  Steady output: Connected to the QNet network.  |
 +
 +{{page>en:software:qworkbench:utility:qrm:BridgeConfigurator}}