| Both sides previous revision Previous revision Next revision | Previous revision |
| en:strumenti:qmoveplus:c1r44:p1r44f-001:mdi_p1r44f-009 [2022/12/05 09:36] – [Table] qem215 | en:strumenti:qmoveplus:c1r44:p1r44f-001:mdi_p1r44f-009 [2023/07/26 09:09] (current) – [Table] qem215 |
|---|
| ^ Editor: | Andrea Zarantonello ||| | ^ Editor: | Andrea Zarantonello ||| |
| ^ Approver: | Giuliano Tognon ||| | ^ Approver: | Giuliano Tognon ||| |
| ^ Link: | http://www.qem.eu/doku/doku.php/strumenti/qmoveplus/c1r44/p1r44f-001/mdi_p1r44f-009 ||| | ^ Link: | https://www.qem.eu/doku/doku.php/strumenti/qmoveplus/c1r44/p1r44f-001/mdi_p1r44f-009 ||| |
| ^ Language: | English ||| | ^ Language: | English ||| |
| | |||| | | |||| |
| Machine view from above: | Machine view from above: |
| |
| {{:strumenti:qmoveplus:c1r44:p1r44f-001:macchina_alto_mdi.png?nolink&800|}} | {{:strumenti:qmoveplus:c1r44:p1r44f-001:macchina_generale.png?nolink&800|}} |
| |
| ^ n: ^ Description: ^ | ^ n: ^ Description: ^ |
| | 1 | Raw slab | | | 1 | Raw slab | |
| | 2 | Tape Encoder | | | 2 | Belt Encoder | |
| | 3 | Limit sensor bar | | | \\ 3 | Limit sensor bar\\ First sensor: F {{:strumenti:qmoveplus:c1r44:p1r44f-001:blue_riquadro.png?10&nolink}}\\ Last sensor: L {{:strumenti:qmoveplus:c1r44:p1r44f-001:viola_riquadro.png?10&nolink}} | |
| | 4 | Center of the sensors / centre of the bridge axis travel | | | 4 | Center of the sensors / centre of the bridge axis travel | |
| | 5 | Bridge | | | 5 | Bridge | |
| | 6 | Polishing heads | | | 6 | Polishing heads | |
| | 7 | Belt direction| | | 7 | Belt direction | |
| | 8 | Orthogonal Offset | | | 8 | Orthogonal Offset | |
| | | 0 count | Counting 0 of the bridge | |
| |
| <html><pagebreak /></html> | <html><pagebreak /></html> |
| | **PG32** : REFERENCE VEL | m / ' | 0.0 | 0 ÷ 9999.9 | Reference speed for the use of the advances and delays of the brush. \\ If set to 0, no speed proportion is made but the set quotas are used. | | | **PG32** : REFERENCE VEL | m / ' | 0.0 | 0 ÷ 9999.9 | Reference speed for the use of the advances and delays of the brush. \\ If set to 0, no speed proportion is made but the set quotas are used. | |
| | **PG34** : RAMP TYPE | - | 1 | 0 ÷ 1 | Type of ramp.\\ 0 = linear ramp.\\ 1 = S ramp | | | **PG34** : RAMP TYPE | - | 1 | 0 ÷ 1 | Type of ramp.\\ 0 = linear ramp.\\ 1 = S ramp | |
| | | **PG35** : HEAD SEGMENTATION | - | 4 | 4 - 6 | Segmentation of the head machining area | |
| | | **PG36** : MAX SET SPEED | m/min | 50 | 0 ÷ 999.9 | Maximum belt settable speed | |
| | | **PG37** : MIN SET SPEED | m/min | 0.0 | 0 ÷ 999.9 | Minimum belt settable speed | |
| <html><pagebreak /></html> | <html><pagebreak /></html> |
| |
| |
| ^ //**Parameter name**// ^ //**Unit of measure**// ^ //**Default **// ^ //**Range**// ^ //**Description**// ^ | ^ //**Parameter name**// ^ //**Unit of measure**// ^ //**Default **// ^ //**Range**// ^ //**Description**// ^ |
| | MEASURE | mm | 0.1 | 0 ÷ 99999.9 | Indicates the space, in units of measure, covered by the tape to obtain the encoder pulses set on the //pulse// parameter. | | | MEASURE | mm | 0.1 | 0 ÷ 99999.9 | Indicates the space, in units of measure, covered by the belt to obtain the encoder pulses set on the //pulse// parameter. | |
| | PULSE | - | 1 | 0 ÷ 999999 | Indicates the pulses multiplied by 4 provided by the tape encoder to obtain the gap set in the measure parameter.\\ The ratio between measure and pulse is the resolution of the encoder and must have values between 1 and 0.000935. | | | PULSE | - | 1 | 0 ÷ 999999 | Indicates the pulses multiplied by 4 provided by the belt encoder to obtain the gap set in the measure parameter.\\ The ratio between measure and pulse is the resolution of the encoder and must have values between 1 and 0.000935. | |
| | |
| | Press {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:button_120x60_forward_002_.png?nolink&100|}} to go to Belt setup page. |
| | |
| | ==== Belt calibration==== |
| | |
| | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_calibration_en.png?nolink&500|}} |
| | |
| | ^ //**Parameter name**// ^ //**Unit of measurement**// ^ //**Default**// ^ //**Range**// ^ //**Description**// ^ |
| | | VOLTAGE OUTPUT | V | 0.0 | 0 ÷ 10.0 | Control voltage Inverter/Driver | |
| | | OFFSET | V | 0.0000 | -99.9999 ÷ 99.9999 | Voltage value to obtain from the analog output 0 Volt | |
| | | SPEED | mm/' | - | - | Speed of the belt | |
| | | MAX SPEED | mm/' | 5000 | 0 ÷ 9999999 | Speed of the belt with the 10 Volt command | |
| | | POSITION | mm | - | - | Belt position | |
| | |
| | <html><pagebreak /></html> |
| =====- Setup Bridge ===== | =====- Setup Bridge ===== |
| {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:bridge_setup.png?nolink&500|}} | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:bridge_setup.png?nolink&500|}} |
| |
| The calibration pages are divided into: | The calibration pages are divided into: |
| | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:resolution_en.png?300&nolink}} | setting the resolution of the axis\\ \\ \\ \\ \\ \\ \\ axis calibration procedure for adjusting the feedback and for setting the offset and maximum speed | | | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:resolution_en.png?300&nolink}} | setting the resolution of the axis\\ \\ \\ \\ \\ \\ axis calibration procedure for adjusting the feedback and for setting the offset and maximum speed | |
| |
| ==== Bridge axis resolution ==== | ==== Bridge axis resolution ==== |
| {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:bridge_resolution.png?nolink&500|}} | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:bridge_resolution.png?nolink&500|}} |
| |
| ^ //**Parameter name**// ^ //**Unit of measure**// ^ //**Default **// ^ //**Range**// ^ //**Description**// ^ | ^ //**Parameter name**// ^ //**Unit of measure**// ^ //**Default **// ^ //**Range**// ^ //**Description**// ^ |
| | MEASURE | mm | 0.1 | 0 ÷ 99999.9 | Indicates the space, in units of measure, covered by the tape to obtain the encoder pulses set on the //pulse// parameter. | | | MEASURE | mm | 0.1 | 0 ÷ 99999.9 | Indicates the space, in units of measure, covered by the bridge to obtain the encoder pulses set on the //pulse// parameter. | |
| | PULSE | - | 1 | 0 ÷ 999999 | Indicates the pulses multiplied by 4 provided by the tape encoder to obtain the gap set in the measure parameter.\\ The ratio between measure and pulse is the resolution of the encoder and must have values between 1 and 0.000935. | | | PULSE | - | 1 | 0 ÷ 999999 | Indicates the pulses multiplied by 4 provided by the bridge encoder to obtain the gap set in the measure parameter.\\ The ratio between measure and pulse is the resolution of the encoder and must have values between 1 and 0.000935. | |
| |
| |
| <html><pagebreak /></html> | <html><pagebreak /></html> |
| |
| | ====== - Support ====== |
| | |
| | ===== Request for assistance ===== |
| | |
| | In order to be able to provide you a quick service, at the minimum cost, we need your help. |
| | |
| | | {{doc:assistenza:assistenza_1.png?nolink&100}} | {{doc:assistenza:assistenza_modulo_01.png?nolink&100}} | |
| | | Follow all the instructions provided in the manual [[appnote: mimat|MIMAT]] | If the problem persists, fill in the "Assistance request form" on the page [[https://www.qem.it/index.php/en/contact-request.html | Contacts]] of the site www.qem.it. \\ Our technicians will obtain essential elements for understanding your problem. | |
| | |
| | ===== Repair ===== |
| | |
| | In order to provide you with an efficient service, please read and follow the instructions here [[en/assistenza_tecnica:riparazione|reported]] |
| | |
| | ===== Shipping ===== |
| | |
| | It is recommended to pack the instrument with materials that can absorb any falls. |
| | | {{doc:assistenza:assistenza_4.png?100&nolink}} | {{doc:assistenza:assistenza_5.png?100&nolink}} | {{doc:assistenza:assistenza_6.png?100&nolink}} | |
| | | Use the original packaging: it must protect the instrument during transport. | Attach: \\ 1. A description of the anomaly; \\ 2. Part of the wiring diagram where the instrument is inserted \\ 3. Programming the instrument ( set up, work quotas, parameters ...). | A thorough description of the problem will allow us to quickly identify and resolve your problem.\\ Careful packaging will avoid further inconveniences. | |