Differences
This shows you the differences between two versions of the page.
| en:strumenti:qmoveplus:j1k31:p1k31fr30-001:mce_p1k31fr30-001 [2015/01/26 10:44] – [2.4. Analog inputs (n. 4)] qem102 | en:strumenti:qmoveplus:j1k31:p1k31fr30-001:mce_p1k31fr30-001 [2019/08/29 17:01] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== P1K31FR30-001 - 3 axis bridge saw: Wiring Connections ====== | ||
| + | |||
| + | {{ : | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | <WRAP center round box 90%> | ||
| + | | {{: | ||
| + | ^ Document | ||
| + | ^ Description | ||
| + | ^ Drawn up | Riccardo Furlato | ||
| + | ^ Approved | ||
| + | ^ Link: | http:// | ||
| + | ^ Languages | ||
| + | | |||| | ||
| + | ^ Release | ||
| + | | 01 | New Manual | ||
| + | |||
| + | |||
| + | </ | ||
| + | |||
| + | ---- | ||
| + | |||
| + | <wrap lo> | ||
| + | All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation. | ||
| + | QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information in this document can be changed without notice. QEM shall not be held liable for any error or omission in this document. | ||
| + | QEM® is a registered trademark.Microsoft® and MS-DOS® are registered trademarks and Windows® is a trademark of Microsoft Corporation. | ||
| + | </ | ||
| + | |||
| + | < | ||
| + | |||
| + | |||
| + | ====== - Hardware ====== | ||
| + | ^ **J1-K31-FR30** | ||
| + | | {{: | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | < | ||
| + | |||
| + | |||
| + | ====== - I/O Resources ====== | ||
| + | |||
| + | |||
| + | ==== - Digital Inputs used (n. 38) ==== | ||
| + | |||
| + | * NO = Normally Open | ||
| + | * NC = Normally Closed | ||
| + | * I = Impulsive | ||
| + | * C = Continuous | ||
| + | |||
| + | ^ NAME | ||
| + | | I33 | Lathe one revolution sensor | ||
| + | | ∩ | Connect to PIN CN11.3 | ||
| + | | 0V | Common for digital inputs | ||
| + | | I1 | JOG X + | NO | ||
| + | | I2 | JOG X - | NO | ||
| + | | I3 | JOG Y + | NO | ||
| + | | I4 | JOG Y - | NO | ||
| + | | I5 | JOG Z + | NO | ||
| + | | I6 | JOG Z - | NO | ||
| + | | I7 | Start work cycle | ||
| + | | I8 | Stop work cycle | NC | ||
| + | | 0V | Common for digital inputs | ||
| + | | I34 | Mill inverter on | ||
| + | | ∩ | Connect to PIN CN12.3 | ||
| + | | 0V | Common for digital inputs | ||
| + | | I9 | Enable manual mode | ||
| + | | I10 | Enable automatic mode | NO | ||
| + | | I11 | Clear work and all axes | NO | ||
| + | | I12 | Fast JOG | ||
| + | | I13 | Water pressure OK | NC | ||
| + | | I14 | Power system OK | NC | ||
| + | | I15 | Not used | ||
| + | | I16 | Rotary table down | NO | ||
| + | | 0V | Common for digital inputs | ||
| + | | I35 | Disk inverter on | ||
| + | | ∩ | Connect to PIN CN13.3 | ||
| + | | 0V | Common for digital inputs | ||
| + | | I17 | Drives OK | NC | ||
| + | | I18 | Enclosure protection OK | NC | ||
| + | | I19 | X limit switch | ||
| + | | I20 | Y limit switch | ||
| + | | I21 | Z limit switch | ||
| + | | I22 | W unlock position 1 ok | ||
| + | | I23 | W unlock position 2 ok | ||
| + | | I24 | Y parking switch | ||
| + | | 0V | Common for digital inputs | ||
| + | | I36 | Inverter ok | NO | ||
| + | | ∩ | Connect to PIN CN14.3 | ||
| + | | 0V | Common for digital inputs | ||
| + | | I25 | Horizontal disk | NO | ||
| + | | I26 | Vertical disk | NO | ||
| + | | I27 | X Homing Switch | ||
| + | | I28 | Y Homing Switch | ||
| + | | I29 | Z Homing Switch | ||
| + | | I30 | W Homing Switch | ||
| + | | I31 | H Homing Switch | ||
| + | | I32 | Spindle speed ok | ||
| + | | 0V | Common for digital inputs | ||
| + | | I37 | H unlock position 1 ok | ||
| + | | I38 | H unlock position 2 ok | ||
| + | | / | //Not used// | ||
| + | | ∩ | Connect to PIN CN21.5B | ||
| + | | ∩ | Connect to PIN CN21.6B | ||
| + | | 0V | Common for digital inputs | ||
| + | | {{: | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | < | ||
| + | |||
| + | |||
| + | ==== - Digital outputs used (n. 30) ==== | ||
| + | |||
| + | ^ NAME ^ DESCRIPTION | ||
| + | | V+ |Voltage Input (12÷28 Vdc)|{{connettori: | ||
| + | | O1 |Automatic cycle running|::: | ||
| + | | O2 |//Not used// | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O3 |Alarm sound |:::| CN7.5 |:::| | ||
| + | | O4 |Rotary table up|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O5 |Rotary table down|::: | ||
| + | | O6 |//Not used// | ||
| + | | O7 |X enable|::: | ||
| + | | O8 |Laser 2 |:::| CN7.11 | ||
| + | | V+ |Voltage Input (12~28 Vdc)|::: | ||
| + | | O9 |Y enable|::: | ||
| + | | O10 |Y brake|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O11 |Z enable|::: | ||
| + | | O12 |Z brake|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O13 |W enable|::: | ||
| + | | O14 |W enable reference|::: | ||
| + | | O15 |W brake|::: | ||
| + | | O16 |H enable|::: | ||
| + | | V+ |Voltage Input (12~28 Vdc)|::: | ||
| + | | O17 |H enable reference|::: | ||
| + | | O18 |H brake|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O19 |Water valve|::: | ||
| + | | O20 |Laser 1|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O21 |Reset drives|::: | ||
| + | | O22 |Tilting table pump|::: | ||
| + | | O23 |End of automatic work|::: | ||
| + | | O24 |Machine OK|::: | ||
| + | | V+ |Voltage Input (12~28 Vdc)|{{connettori: | ||
| + | | O25 |Mill inverter enable|::: | ||
| + | | O26 |Disk inverter enable|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O27 |Open enclosure protection|::: | ||
| + | | O28 |Inverter run command|::: | ||
| + | | V- |Common Voltage input (0V)|::: | ||
| + | | O29 |W lock position 1 ON|::: | ||
| + | | O30 |W lock position 2 ON|::: | ||
| + | | O31 |H lock position 1 ON|::: | ||
| + | | O32 |H lock position 2 ON|::: | ||
| + | | - - - - - | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | - | - - - - - - - - - | - | | ||
| + | < | ||
| + | |||
| + | |||
| + | ==== - Two-way encoder count inputs used (n° 6) ==== | ||
| + | |||
| + | |||
| + | ^ // | ||
| + | ^ NAME ^ DESCRIPTION | ||
| + | | CNT01 |X position - Channel A |{{connettori: | ||
| + | | CNT01 |X position - Channel B |:::| CN15.3A | ||
| + | | CNT01 |X position - Z |:::| CN15.4A | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | CNT02 |Y position - Channel A |:::| CN16.2A | ||
| + | | CNT02 |Y position - Channel B |:::| CN16.3A | ||
| + | | CNT02 |Y position - Z |:::| CN16.4A | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | CNT03 |Z position - Channel A |:::| CN17.2A | ||
| + | | CNT03 |Z position - Channel A |:::| CN17.3A | ||
| + | | CNT03 |Z position - Z |:::| CN17.4A | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | CNT04 |W position - Channel A |:::| CN18.2A | ||
| + | | CNT04 |W position - Channel B |:::| CN18.3A | ||
| + | | CNT04 |W position - Z |:::| CN18.4A | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | CNT05 |H position - Channel A |:::| CN19.2A | ||
| + | | CNT05 |H position - Channel B |:::| CN19.3A | ||
| + | | CNT05 |H position - Z |:::| CN19.4A | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | CNT06 |Work speed potentiometer - Channel A |{{connettori: | ||
| + | | CNT06 |Work speed potentiometer - Channel B |:::| CN20.3A | ||
| + | | CNT06 |Work speed potentiometer - Z | ||
| + | | ∩ |Connect to PIN CNn.5B | ||
| + | | ∩ |Connect to PIN CNn.6B | ||
| + | | 0V | ||
| + | | - - - - - | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | | ||
| + | \\ | ||
| + | |||
| + | ^ // | ||
| + | ^ NAME ^ DESCRIPTION | ||
| + | | CNTxx |Channel A+ |{{connettori: | ||
| + | | CNTxx |Channel B+ |:::| CN15.3B | ||
| + | | CNTxx |Z+ |:::| CN15.4B | ||
| + | | CNTxx |Channel A- | ||
| + | | CNTxx |Channel B- | ||
| + | | CNTxx |Z- |:::| CN15.7B | ||
| + | | 0V | ||
| + | | - - - - - | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | | ||
| + | |||
| + | < | ||
| + | |||
| + | |||
| + | ==== - Analog inputs used (n. 4) ==== | ||
| + | |||
| + | ^ NAME ^ DESCRIPTION | ||
| + | | GAI |Common for analog inputs |{{connettori: | ||
| + | | IA1 |X speed potentiometer |:::| CN28.2 | ||
| + | | / | // Not Used // |:::| CN28.3 | ||
| + | | / | // Not Used // |:::| CN28.4 | ||
| + | | GAI |Common for analog inputs |:::| CN28.5 | ||
| + | | IA2 |X backward speed potentiometer |:::| CN28.6 | ||
| + | | / | // Not Used // |:::| CN28.7 | ||
| + | | / | // Not Used // |:::| CN28.8 | ||
| + | | VRef |Voltage reference |:::| CN28.9 | ||
| + | | GAI |Common for analog inputs |:::| CN29.1 | ||
| + | | IA3 |Spindle current reading |:::| CN29.2 | ||
| + | | ∩ |For 0~10V signal - Connect to GAI |:::| CN29.3 | ||
| + | | ∩ |For 0~20mA signal - Connect to GAI |:::| CN29.4 | ||
| + | | GAI |Common for analog inputs|::: | ||
| + | | IA4 |Spindle rpm reading|::: | ||
| + | | ∩ |For 0~10V signal - Connect to GAI |:::| CN29.7 | ||
| + | | ∩ |For 0~20mA signal - Connect to GAI |:::| CN29.8 | ||
| + | | VRef | Voltage reference |:::| CN28.9 | ||
| + | | - - - - - - - | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | - | - - - - - - - - - | - | | ||
| + | \\ | ||
| + | |||
| + | |||
| + | ==== - Analog outputs used (n. 6) ==== | ||
| + | |||
| + | ^ NAME ^ DESCRIPTION | ||
| + | | GAO |Common for analog outputs|{{connettori: | ||
| + | | AO1 |X Speed +/-10V command|::: | ||
| + | | AO2 |Y Speed +/-10V command|::: | ||
| + | | GAO |Common for analog outputs|::: | ||
| + | | AO3 |Z Speed +/-10V command|::: | ||
| + | | AO4 |W Speed +/-10V command|::: | ||
| + | | GAO |Common for analog outputs|::: | ||
| + | | AO5 |H Speed +/-10V command|::: | ||
| + | | AO6 |Spindle rotation speed set |::: | ||
| + | | GAO |Common for analog outputs|::: | ||
| + | | / | //Not Used// |::: | ||
| + | | / | //Not Used// |::: | ||
| + | | - - - - - | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | - | - - - - - - - - - | - | | ||
| + | |||
| + | |||
| + | |||