Differences

This shows you the differences between two versions of the page.

--- en:strumenti:qmoveplus:j1p20:p1p20f-022:mdi_p1p20f-022 [2020/11/26 12:14] – [9.1.2 Motors Start on RMC Module (MP-05=2)] qem103
+++ en:strumenti:qmoveplus:j1p20:p1p20f-022:mdi_p1p20f-022 [2021/01/26 14:28] (current) – [5.3.2 Machine parameters] qem201
@@ Line 249: / Line 249: @@
 |**GP-17**|-|0|0 ÷ 1|**Carter Contact** Activation Status.\\ **0** = NC (**N**ormally **C**losed )\\ **1** = NO (**N**ormally **O**pen)|
 |**GP-18**|-|4000 |P (Pulse) Encoder Bridge |**Bridge encoder pulses** x 4 corresponding to the space set in the **Measure**.|
-|**GP-19**|-|400.0|M (Measure) Ponte |**Bride Space** corresponding to the encoder pulses in the **Pulse** parameter.\\ **Note:**\\ - the P/M ratio must be between 0.000935 and 4.000000.|
+|**GP-19**|-|400.0|M (Measure) Encoder Bridge |**Bridge Space** corresponding to the encoder pulses in the **Pulse** parameter.\\ **Note:**\\ - the P/M ratio must be between 0.000935 and 4.000000.|
-|**GP-20**|-|1|0 ÷ 3|**Decimal poiint position** on the **speed** Bridge view.\\ **0**=xxxx, **1**=xxx.x, **2**=xx.xx, **3**=x.xxx|
+|**GP-20**|-|1|0 ÷ 3|**Decimal point position** on the **speed** Bridge view.\\ **0**=xxxx, **1**=xxx.x, **2**=xx.xx, **3**=x.xxx|
 |**GP-21**|-|1|0 ÷ 3|**Decimal point position** on the **measure** Bridge view.\\ **0**=xxxx, **1**=xxx.x, **2**=xx.xx, **3**=x.xxx|
 |**GP-22**|-|2000|-99999 ÷ 999999|**Maximum measure** of the Bridge.|
@@ Line 302: / Line 302: @@
 |**MP-09**|m/'|3.0|0 ÷ 5.0|**Speed in automatic** of the **conveyor belt**\\ (//MP-03// > 0)|
 |**MP-10**|m/'|1.0|0 ÷ 5.0|**Jog speed** of the **conveyor belt**\\ (//MP-03// > 0).|
-|**MP-11**|-|0|0 ÷ 1|__**Starting condition** of the bridge in automatic mode__ (//MP-04// = 1).\\ **0** = Start with tape\\ **1** = Start when a piece enter|
+|**MP-11**|-|0|0 ÷ 1|__**Starting condition** of the bridge in automatic mode__ (//MP-04// = 1).\\ **0** = Start with conveyor belt\\ **1** = Start when a piece enter|
 |**MP-12**|s|1.000|0 ÷ 999.0|**Delay time** between the conveyor belt start and bridge start (//MP-05// = 1).|
 |**MP-13**|%|5.0|0 ÷ 100.0|**% maximum speed** of the bridge in automatic mode.|
@@ Line 671: / Line 671: @@
   - After the //t1// time (time interval motors start) you have the output activation for the next head enabled in set-up.
   - In the event that a start motor command is activated again (**I3**) is not processed. A new start command will only be processed in case the instrument first goes into operation activation heads (**O17** = OFF) and then come back in start motors operation mode (**O17** = ON).
-  - The output of the last enabled head is activated and the start motor procedure is completed.
+  - The output of the last enabled head is activated and the start motors procedure is completed.
   - The **O18** output is activated after the //t2// time (The time between the start-up of the last motor and the activation of the end-of-motor output **O18**).
-  - Turn off the **I2** input and the instrument changes the way of operation from starting motors to head startin. All head-related outputs (**O1÷O16**) and the **O18** outputs are deactivated.
+  - Turn off the **I2** input and the instrument changes the way of operation from starting motors to head starting. All head-related outputs (**O1÷O16**) and the **O18** outputs are deactivated.
   - After the //t4// time (start-activation step time) the instrument turns off the **O17** output and enables the heads activation operation mode.
 ==== - Motors Start on RMC Module (MP-05=2) ====
@@ Line 694: / Line 694: @@
   - After the //t1// time (time interval motors start) you have the output activation for the next head enabled in set-up.
   - In the event that a start motor command is activated again (**I3**) 5. is not processed.
-  - The output of the last enabled head is activated and the start motor procedure is completed.
+  - The output of the last enabled head is activated and the start motors procedure is completed.
   - The **O18** output is activated after the //t2// time (The time between the start-up of the last motor and the activation of the end-of-motor output **O18**).
-==== - Avviamento Motori su Modulo RMC (MP-05=3) ====
+==== - motors Start on RMC Module (MP-05=3) ====
-La sequenza di avviamento motori utilizza le uscite utilizzate nel modulo RMC.
+The motor start sequence uses the outputs in the RMC module.
-L'Ingresso I2 non ha nessun funzionamento.
+I2 input has no operation.
-\\ L'ingresso I3 non ha nessun funzionamento.
+\\ Input I3 starts the motor start sequence.
-La sequenza di "avviamento motori" viene avviata automaticamente non appena "entra" il primo pezzo in macchina.
+The "motor start" sequence is started automatically as soon as the first piece "enters" the machine.
-N.B. Quando l'ultimo pezzo lavorato "esce" dalla macchina, le uscite avviamento motori si disattivano.
+N.B. When the last worked piece "comes out" of the machine, the motor start outputs are deactivated.
-Qui di seguito il diagramma di funzionamento della sequenza avvio motori con il parametro **//MP-05=3//**.
+Below is the diagram of how the motor start sequence works with the **//MP-05=3//**.
 {{:strumenti:qmoveplus:j1p20:p1p20f-022:various:sequenza_avviamento_3.png?680}}
@@ Line 712: / Line 712: @@
 **Legenda** \\
-  * **I9** = Acquisizione pezzo
+  * **I9** = Piece acquisition
-  * **O25÷O44** = Comando teste 1÷20
+  * **O25÷O44** = Heads commad 1÷20
-  * **O18** = Fine avviamento
+  * **O18** = End of start-up
-  - All'attivazione dell'ingresso **I9** si ha l'inizio della procedura di partenza in cascata dei motori e si attiva l'uscita relativa alla prima testa abilitata in set-up in ordine crescente.
+  - When activating the **I9** 3. input you have the beginning of the procedure of cascading motors and you activate the output relative to the first set-up-enabled head in ascending order.
-  - Trascorso il tempo //t1// (tempo intervallo start motori) si ha l'attivazione dell'uscita relativa alla successiva testa abilitata in set-up.
+  - After the //t1// time (4. time interval motors start) you have the output activation for the next head enabled in set-up.
-  - Trascorso il tempo //t1// (tempo intervallo start motori) si ha l'attivazione dell'uscita relativa alla successiva testa abilitata in set-up.
+  - The output of the last enabled head is activated and the start motors procedure is completed.
-  - Si attiva l'uscita dell'ultima testa abilitata e ha termine la procedura di start motori.
+  - The **O18** output is activated after the //t2// time (The time between the start-up of the last motor and the activation of the end-of-motor output **O18**).
-  - Si attiva l'uscita **O18** dopo il tempo //t2// (Tempo che intercorre tra l'avviamento dell'ultimo motore e l'attivazione dell'uscita di fine avviamento motori **O18**).
 <html><pagebreak /></html>