Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
en:strumenti:qmoveplus:j1p44:p1p44f-010:mce_p1p44f-010 [2020/03/20 14:42] – [Table] qem103 | en:strumenti:qmoveplus:j1p44:p1p44f-010:mce_p1p44f-010 [2021/04/21 18:07] (current) – [Table] qem103 | ||
---|---|---|---|
Line 18: | Line 18: | ||
^ Document release | ^ Document release | ||
| 01 | New manual | | 01 | New manual | ||
+ | | 02 | Add the Alarm 2 output on the second RMC-1S module | ||
+ | | 03 | Can speed modifity to 500Kb | ||
+ | | 04 | Add the I70 input and O63 output for hydraulic brakes (wedges) | ||
</ | </ | ||
+ | |||
==== - Specifications ==== | ==== - Specifications ==== | ||
Line 77: | Line 81: | ||
== - CAN port settings == | == - CAN port settings == | ||
- | ^ SW1 ^ Num.\\ Dip ^ Set ^ | + | ^ SW1 |
- | | {{:strumenti:qmoveplus: | + | | {{:dip-switch:dip-8.jpg?80}} | 1 |
- | | ::: | + | | ::: | 2 |
- | | ::: | + | | ::: | 3 |
- | | ::: | + | | ::: | 4 |
- | | ::: | + | | ::: | 5 |
- | | ::: | + | | ::: | 6 |
- | | ::: | + | | ::: | 7 |
- | | ::: | + | | ::: | 8 |
< | < | ||
Line 323: | Line 327: | ||
**Functions Description** | **Functions Description** | ||
- | ^ **SW2** | + | ^ **SW2** |
- | | {{: | + | | {{: |
- | | ::: | ::: | 2 | ON | | + | | ::: | ::: |
- | | ::: | ::: | Baud-Rate | + | | ::: | ::: |
- | | ::: | //Selecting the address of the Canbus slave module// | + | | ::: | //Selecting the address of the Canbus slave module// |
- | | ::: | ::: | 4 | OFF | | + | | ::: | ::: |
- | | ::: | ::: | 5 | OFF | | + | | ::: | ::: |
- | | ::: | ::: | 6 | OFF | | + | | ::: | ::: |
- | | ::: | ::: | ID | + | | ::: | ::: |
< | < | ||
Line 343: | Line 347: | ||
=== - CN6 === | === - CN6 === | ||
- | ^ ^ PIN (NUMBER) | + | ^ ^ PIN (NUMBER) |
- | | {{ : | + | | {{ : |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
~~REFNOTES~~ | ~~REFNOTES~~ | ||
Line 575: | Line 579: | ||
^ **SW2** | ^ **SW2** | ||
- | | {{: | + | | {{: |
| ::: | ::: | | ::: | ::: | ||
- | | ::: | ::: | + | | ::: | ::: |
| ::: | //Selecting the address of the Canbus slave module// | | ::: | //Selecting the address of the Canbus slave module// | ||
| ::: | ::: | | ::: | ::: | ||
Line 597: | Line 601: | ||
| {{ : | | {{ : | ||
| ::: | | ::: | ||
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
| ::: | | ::: | ||
| ::: | | ::: | ||
Line 614: | Line 618: | ||
| ::: | | ::: | ||
+ | ~~REFNOTES~~ | ||
== - NPN logic connections example == | == - NPN logic connections example == | ||
- | {{: | + | {{: |
== - PNP logic connections example == | == - PNP logic connections example == | ||
- | {{: | + | {{: |
<WRAP leftalign round tip 60%> | <WRAP leftalign round tip 60%> | ||
Line 760: | Line 764: | ||
| ::: | | ::: | ||
| ::: | | ::: | ||
- | | ::: | + | | ::: |
- | | ::: | + | | ::: |
| ::: | | ::: | ||
| ::: | | ::: |