Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
en:strumenti:qmoveplus:mim1ms3f01 [2016/08/24 16:45] – [4. Caratteristiche elettriche] qem103 | en:strumenti:qmoveplus:mim1ms3f01 [2016/09/14 16:35] – [Informations] qem103 | ||
---|---|---|---|
Line 12: | Line 12: | ||
^ Editor: | ^ Editor: | ||
^ Approver: | ^ Approver: | ||
- | ^ Link: | http:// | + | ^ Link: | http:// |
^ Language: | ^ Language: | ||
| ||||| | | ||||| | ||
Line 134: | Line 134: | ||
===== - Ingressi ===== | ===== - Ingressi ===== | ||
- | ==== - Ingressi digitali | + | ==== - Digital inputs |
- | |Tipo di polarizzazione | PNP | | + | |Polarization type | PNP | |
- | |Tempo min. di acquisizione | + | |Minimum time of acquisition |
- | |Isolamento | + | |Insulation |
- | |Tensione di funzionamento nominale | + | |Nominal working voltage |
- | |Tensione massima applicabile | + | |Maximum applicable voltage |
- | |Tensione stato logico | + | |Logical state voltage |
- | |Tensione stato logico | + | |Logical state voltage |
- | |Caduta di tensione interna | + | |Internal voltage drop |
- | |Resistenza di ingresso | + | |Input resistance |
- | |Corrente massima assorbita | + | |Maximum absorbed current |
- | |Corrente massima erogabile | + | |Maximum supply current |
- | ==== - Ingresso di conteggio | + | ==== - Counter input ==== |
- | ^:tip:^I valori riportati | + | ^:tip:^The values given in the table refer to A, B e Z input signals.\\ The maximum frequency value, given on the table refer to A e B phase input signal with DutyCycle = 50%\\ With counter frequencies more than 50KHz is preferable to the use of Line-Driver |
. | . | ||
- | |Tipo di polarizzazione| PNP/ | + | |Polarization type| PNP/ |
- | |Frequenza massima| 15KHz | | + | |Maximum frequency| 15KHz | |
- | |Tempo min. di acquisizione| FIXME | | + | |Minimum time of acquisition| FIXME | |
- | |Isolamento| 1000Vrms | + | |Insulation| 1000Vrms |
- | |Tensione di funzionamento nominale| 5Vdc | | + | |Nominal working voltage| 5Vdc | |
- | |Tensione stato logico | + | |Logical state voltage |
- | |Tensione stato logico | + | |Logical state voltage |
- | |Caduta di tensione interna| 1.2V | | + | |Internal voltage drop| 1.2V | |
- | |Resistenza di ingresso| 1200O | | + | |Input resistance| 1200O | |
< | < | ||
Line 166: | Line 166: | ||
===== - STEP-DIRECTION outputs ===== | ===== - STEP-DIRECTION outputs ===== | ||
- | |Tipo di polarizzazione| Push-Pull / Line-Driver | + | |Polarization type| Push-Pull / Line-Driver |
- | |Massima frequenza d' | + | |Maximum output frequency| 300KHz |
- | |Isolamento| 1000Vpp | + | |Insulation| 1000Vpp |
- | |Corrente max. di funzionamento| 20mA | | + | |Max working current| 20mA | |
- | |Tensione nominale| | + | |Rated voltage| |
- | {{schemi: | + | {{schemi: |
- | stepper}} | + | |