Differenze
Queste sono le differenze tra la revisione selezionata e la versione attuale della pagina.
Entrambe le parti precedenti la revisione Revisione precedente Prossima revisione | Revisione precedente Prossima revisioneEntrambe le parti successive la revisione | ||
software:profileimporter:profile_importer_8.1 [2022/10/07 10:56] – [4.2.4.1 Mode 1] qem214 | software:profileimporter:profile_importer_8.1 [2022/10/07 11:38] – [5.1 DXF Requirements] qem214 | ||
---|---|---|---|
Linea 92: | Linea 92: | ||
Una volta completata l' | Una volta completata l' | ||
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
- | Per assicurarsi che il QRM sia attivo è necessario verificare che appaia questa icona.{{: | + | Per assicurarsi che il QRM sia attivo è necessario verificare che appaia questa icona.{{: |
</ | </ | ||
Linea 195: | Linea 195: | ||
Scarica le geometrie su Qmove control attraverso le risorse fornite dalla connessione QRM (seriale o Ethernet). | Scarica le geometrie su Qmove control attraverso le risorse fornite dalla connessione QRM (seriale o Ethernet). | ||
- | * Seleziona //Abilita Invia a destinazione//. | + | * Seleziona //Enable Send to Target//. |
- | * Fare clic su //Resource ID// e scegliere una delle risorse dell' | + | * Fare clic su //Resource ID// e scegliere una delle risorse dell' |
{{: | {{: | ||
Linea 269: | Linea 269: | ||
|Salva su file e/o CSV| | |Salva su file e/o CSV| | ||
- | === - Mode 2 === | + | === - Modalità |
- | Mode 2 is only allowed when the application is in programming mode, otherwise the download | + | La modalità |
- | Download the geometries to Qmove control | + | Scarica le geometrie su Qmove control |
- | * Select | + | * Seleziona |
- | * Click su //Resurce | + | * Fare clic su //Resource |
{{: | {{: | ||
- | To configure the resources that the PC and the network to which the PC is connected, you must act provides | + | Per configurare le risorse che il PC e la rete a cui è collegato il PC, è necessario agire sul software QRM su cui bisogna cliccare due volte {{: |
- | * Use the machine | + | * Utilizzare l'HMI della macchina per visualizzare la pagina predisposta per ricevere i dati. |
- | * Click on // | + | * Fare clic su // |
{{: | {{: | ||
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
- | The second method is only possible if the application is located | + | Il secondo metodo è possibile solo se l' |
- | + | \\ {{: | |
- | {{: | + | |
</ | </ | ||
- | A program description may be entered | + | È possibile inserire una descrizione del programma |
+ | |||
+ | |||
< | < | ||
- | ===== - Options | + | ===== - Opzioni |
- | Options panel could be opened pressing Option button in the main screen. | + | Il pannello delle opzioni può essere aperto premendo il pulsante Opzioni nella schermata principale. |
|{{: | |{{: | ||
- | |Options| | + | |Opzioni| |
- | * //Working type//: Profile Importer 8 allows import either Profiles of Geometry, and either option may be disabled. If both are enabled, processing operations may be selected during the parameter input phase. | + | * //Working type// |
- | * //Scale factor//: | + | * //Scale factor//: |
- | then input 100/1. | + | * //Edge Tolerance// |
- | * //Edge Tolerance// | + | * //Arc Tolerance//: |
- | * //Arc Tolerance//: | + | * //Radius Tolerance//: |
- | * //Radius Tolerance//: | + | |
+ | <wrap hi>N.B. //Edge Tolerance, Arc Tolerance e Radius Tolerance// sono in unità di disegno dxf (mm).</ | ||
- | N.B //Edge Tolerance, Arc Tolerance e Radius Tolerance// are in dxf draw unit (mm). | ||
< | < | ||
- | ====== - Appendix | + | ====== - Appendice |
+ | |||
+ | ===== - Requisiti DXF ===== | ||
+ | |||
+ | I file DXF devono essere versione 12 o successiva, in formato ASCII o binario. Le entità consentite sono LINE, CIRCLE, RECTANGLE, ELLIPSE, SPLINE, POLYLINE, LWPOLINE e ARC.\\ | ||
+ | |||
+ | I gruppi non sono supportati.\\ | ||
+ | |||
+ | È possibile estrarre i dati da un singolo livello. Se il disegno ha più di un layer, Profile Importer chiederà all' | ||
- | ===== - DXF Requirements ===== | + | I file DXF devono avere mm come unità intera. Per esempio: se devo rappresentare una linea di 10 cm, nel file .dxf dovrà essere scritto 100. Se si deve rappresentare una linea di 1,5 mm nel file .dxf dovrà essere scritto 1.5 o 1,5 (a seconda del separatore dei decimali).\\ |
- | DXF files must be version 12 or higher, in ASCII or binary format. The allowed entities are LINE, CIRCLE, RECTANGLE, ELLIPSE, SPLINE, POLYLINE, LWPOLINE and ARC.\\ | ||
- | Groups are not supported.\\ | ||
- | Data from a single layer may be extracted. If drawing has more than one layer, Profile Importer will prompt the user for the layer number at import time.\\ | ||
- | DXF files must have mm as integer unit. | ||
< | < | ||