Differenze
Queste sono le differenze tra la revisione selezionata e la versione attuale della pagina.
Entrambe le parti precedenti la revisione Revisione precedente Prossima revisione | Revisione precedente Prossima revisioneEntrambe le parti successive la revisione | ||
software:profileimporter:profile_importer_8.1 [2022/10/07 11:04] – [4.2.4.2 Mode 2] qem214 | software:profileimporter:profile_importer_8.1 [2022/10/07 11:38] – [5.1 DXF Requirements] qem214 | ||
---|---|---|---|
Linea 92: | Linea 92: | ||
Una volta completata l' | Una volta completata l' | ||
<WRAP center round tip 60%> | <WRAP center round tip 60%> | ||
- | Per assicurarsi che il QRM sia attivo è necessario verificare che appaia questa icona.{{: | + | Per assicurarsi che il QRM sia attivo è necessario verificare che appaia questa icona.{{: |
</ | </ | ||
Linea 195: | Linea 195: | ||
Scarica le geometrie su Qmove control attraverso le risorse fornite dalla connessione QRM (seriale o Ethernet). | Scarica le geometrie su Qmove control attraverso le risorse fornite dalla connessione QRM (seriale o Ethernet). | ||
- | * Seleziona //Abilita Invia a destinazione//. | + | * Seleziona //Enable Send to Target//. |
- | * Fare clic su //Resource ID// e scegliere una delle risorse dell' | + | * Fare clic su //Resource ID// e scegliere una delle risorse dell' |
{{: | {{: | ||
Linea 299: | Linea 299: | ||
- | ===== - Options | + | ===== - Opzioni |
- | Options panel could be opened pressing Option button in the main screen. | + | Il pannello delle opzioni può essere aperto premendo il pulsante Opzioni nella schermata principale. |
|{{: | |{{: | ||
- | |Options| | + | |Opzioni| |
- | * //Working type//: Profile Importer 8 allows import either Profiles of Geometry, and either option may be disabled. If both are enabled, processing operations may be selected during the parameter input phase. | + | * //Working type// |
- | * //Scale factor//: | + | * //Scale factor//: |
- | then input 100/1. | + | * //Edge Tolerance// |
- | * //Edge Tolerance// | + | * //Arc Tolerance//: |
- | * //Arc Tolerance//: | + | * //Radius Tolerance//: |
- | * //Radius Tolerance//: | + | |
+ | <wrap hi>N.B. //Edge Tolerance, Arc Tolerance e Radius Tolerance// sono in unità di disegno dxf (mm).</ | ||
- | N.B //Edge Tolerance, Arc Tolerance e Radius Tolerance// are in dxf draw unit (mm). | ||
< | < | ||
- | ====== - Appendix | + | ====== - Appendice |
+ | |||
+ | ===== - Requisiti DXF ===== | ||
+ | |||
+ | I file DXF devono essere versione 12 o successiva, in formato ASCII o binario. Le entità consentite sono LINE, CIRCLE, RECTANGLE, ELLIPSE, SPLINE, POLYLINE, LWPOLINE e ARC.\\ | ||
+ | |||
+ | I gruppi non sono supportati.\\ | ||
+ | |||
+ | È possibile estrarre i dati da un singolo livello. Se il disegno ha più di un layer, Profile Importer chiederà all' | ||
- | ===== - DXF Requirements ===== | + | I file DXF devono avere mm come unità intera. Per esempio: se devo rappresentare una linea di 10 cm, nel file .dxf dovrà essere scritto 100. Se si deve rappresentare una linea di 1,5 mm nel file .dxf dovrà essere scritto 1.5 o 1,5 (a seconda del separatore dei decimali).\\ |
- | DXF files must be version 12 or higher, in ASCII or binary format. The allowed entities are LINE, CIRCLE, RECTANGLE, ELLIPSE, SPLINE, POLYLINE, LWPOLINE and ARC.\\ | ||
- | Groups are not supported.\\ | ||
- | Data from a single layer may be extracted. If drawing has more than one layer, Profile Importer will prompt the user for the layer number at import time.\\ | ||
- | DXF files must have mm as integer unit. | ||
< | < | ||