Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:software:devices:modbus [2016/12/21 16:56] – [5.3. Richieste di lettura] qem103 | en:software:devices:modbus [2016/12/23 17:04] – [6.1.2. Processo dei parametri tipo iwordNN] qem103 | ||
---|---|---|---|
Line 172: | Line 172: | ||
=== Read Coil === | === Read Coil === | ||
- | Funzione di lettura | + | |
- | impostare | + | Bit read function. You want to read the bits of a slave (// |
- | numero di bit che si intendono leggere. Bisogna impostare | + | (//addr// + //num// - 1) <= 512 e (//tabreg// + //num// - 1) <= 512 otherwise the request will fail (reporting by //wcmd//). |
- | master | + | |
- | soddisfare sempre le seguenti due condizioni:\\ | + | |
- | (//addr// + //num// - 1) <= 512 e (//tabreg// + //num// - 1) <= 512 altrimenti la richiesta non potrà essere eseguita | + | |
=== Read Input === | === Read Input === | ||
- | Funzione di lettura a bit. Si vogliono leggere i bit di un certo slave (// | + | |
+ | Bit read function. To read the bits of a slave (// | ||
=== Read Holding Register === | === Read Holding Register === | ||
- | Funzione di lettura a word. Si vogliono leggere le word di un certo slave (idcard). | + | |
- | Bisogna impostare | + | Word read function. For reading the word of the slave (idcard). |
- | indica il numero di word che si intendono leggere. Bisogna impostare | + | You must to set addr to indicate the address of the word in the slave from which to start reading. The num parameter indicates the number of word to be read. You must set tabreg |
- | dei dai letti” del master | + | (addr + num - 1) <= 32 e (tabreg + num - 1) <= 32 otherwise the request will fail (reporting by wcmd). |
- | Si raccomanda di soddisfare sempre le seguenti due condizioni:\\ | + | |
- | (addr + num - 1) <= 32 e (tabreg + num - 1) <= 32 altrimenti la richiesta non potrà essere eseguita | + | |
- | wcmd). | + | |
=== Read Input Register === | === Read Input Register === | ||
- | Funzione di lettura ingressi a word. Si vogliono leggere i bit di un certo slave (idcard). La funzione è identica alla “Read Holding Register”. Viene impostato il parametro type = 4.\\ Il significato delle due funzione si distingue a livello di protocollo MODBUS. Alcuni slave possono mettere a disposizione delle zone di memoria differenti a seconda se le word lette sono Holding o Input. Nel caso di slave Qmove le due richieste hanno lo stesso effetto. | ||
- | ==== - Richieste di scrittura | + | Word read function. For reading the bit of the slave (idcard). The function is equal to the “Read Holding Register”. sets the parameter type = 4.\\ The meaning of the two functions is distinguished at the level of MODBUS protocol. Some slave can make available different memory areas depending if the read word are Holding or Input. In the case of slave Qmove the two requests have the same effect. |
+ | |||
+ | ==== - Write request | ||
=== Force coil === | === Force coil === | ||
- | Funzione di scrittura bit. Si vogliono scrivere | + | |
- | 5.\\ Bisogna impostare | + | Bit write function. For writing |
- | per indicare l’indice del bit nella “tabella dei dati da scrivere” in cui è contenuto il valore da scrivere. | + | |
=== Force register === | === Force register === | ||
- | Funzione di scrittura singola word. Si vuole scrivere | + | |
- | //type// = 6.\\ Bisogna impostare | + | Word write function. For write (force) the word of a slave (// |
- | impostare | + | |
=== Force multiple coil === | === Force multiple coil === | ||
- | Funzione di scrittura | + | |
- | //type// = 15.\\ Bisogna impostare | + | Multiples |
- | num il numero di bit da scrivere. Bisogna impostare | + | (addr + num - 1) <= 512 e (tabreg + num - 1) <= 512 otherwise the request will fail (reporting by wcmd). |
- | da cui iniziano i valori da scrivere. Si raccomanda di soddisfare sempre le seguenti due condizioni:\\ | + | |
- | (addr + num - 1) <= 512 e (tabreg + num - 1) <= 512 altrimenti la richiesta non potrà essere eseguita | + | |
=== Force multiple register === | === Force multiple register === | ||
- | Funzione di scrittura word multiple. Si vogliono scrivere (forzare) le word di un certo slave (// | ||
- | //type// = 16.\\ Bisogna impostare addr per indicare l’indirizzo della word nello slave in cui si intende scrivere. Si deve | ||
- | impostare in num il numero di word da scrivere. Bisogna impostare tabreg per indicare l’indice della word nella “tabella | ||
- | dei dati da scrivere” da cui iniziano i valori da scrivere. Si raccomanda di soddisfare sempre le seguenti due condizioni: | ||
- | (addr + num - 1) <= 32 e (tabreg + num - 1) <= 32 altrimenti la richiesta non potrà essere eseguita (segnalazione mediante wcmd). | ||
- | ==== - Esempi | + | Multiples word write function. For write (forzare) the word of a slave (// |
+ | (addr + num - 1) <= 32 e (tabreg + num - 1) <= 32 otherwise the request will fail (reporting by wcmd). | ||
+ | |||
+ | ==== - Examples | ||
- | 1) Impostazioni modbus e apertura del canale di comunicazione di tipo seriale | + | 1) Modbus settings and opening of serial communication |
<code QCL> | <code QCL> | ||
modbus.mode = 0 ; modbus master | modbus.mode = 0 ; modbus master | ||
Line 257: | Line 247: | ||
</ | </ | ||
- | 3) Lettura del registro | + | 3) Reading the registry |
<code QCL> | <code QCL> | ||
modbus.idcard = 67 | modbus.idcard = 67 | ||
Line 267: | Line 257: | ||
WAIT modbus.st_sended | WAIT modbus.st_sended | ||
IF (modbus.err) | IF (modbus.err) | ||
- | CALL ErroreModbus | + | CALL ErrorModbus |
ENDIF | ENDIF | ||
- | slVelocita | + | slSpeed |
</ | </ | ||
- | 4) Lettura dei holding register | + | 4) Reading of the holding register |
- | Siccome l’area di scambio dati QCL non supporta l’indirizzo | + | The area of QCL data exchange does not support the address |
<code QCL> | <code QCL> | ||
modbus.idcard = 8 | modbus.idcard = 8 | ||
Line 283: | Line 273: | ||
WAIT modbus.st_sended | WAIT modbus.st_sended | ||
IF (modbus.err) | IF (modbus.err) | ||
- | CALL ErroreModbus | + | CALL ErrorModbus |
ENDIF | ENDIF | ||
| | ||
swTemp1 = modbus.iword10 | swTemp1 = modbus.iword10 | ||
- | slVelocita | + | slSpeed |
slPosiz = modbus.ilong7 | slPosiz = modbus.ilong7 | ||
swTemp1 = modbus.iword15 | swTemp1 = modbus.iword15 | ||
</ | </ | ||
- | ==== - Schema a blocchi | + | ==== - Block diagrams |
{{: | {{: | ||
==== - Broadcast ==== | ==== - Broadcast ==== | ||
- | Il Broadcast è un messaggio speciale che viene inviato dal Master e viene ricevuto contemporaneamente da tutti gli slave | ||
- | connessi. La funzionalitá broadcast (idcard = 0) è supportata solamente in modo master e se viene usato un messaggio | ||
- | con type = 5, 6, 15 e 16 (solo scrittura). In questa modalità lo stato st_sended viene attivato appena terminata la trasmissione | ||
- | e non alla ricezione della conferma dallo slave. Infatti non esiste nessuna risposta degli slave per questo tipo di | ||
- | messaggi. Non è possibile utilizzare il comando SENDSYC. | ||
- | ==== - Identificazione degli Slave ==== | + | The Broadcast is a special message that is sent by the Master and is received simultaneously from all connected slaves. The broadcast function (idcard = 0) is supported only in master mode and if you use a message with type = 5, 6, 15 and 16 (write only). In this mode the st_sended state is activated once ended the transmission and not on receipt of confirmation by the slave. There isn't answer on the slaves to such messages. You cannot use the SENDSYC command. |
- | La scheda quando funziona | + | |
- | di tipo QEM. In caso affermativo determina anche il modello di slave connesso. Questo permette di realizzare una diagnostica | + | ==== - Slaves indentification |
- | sulla corretta configurazione della rete. Non è possibile estendere questo controllo | + | |
- | perché il protocollo non prevede una modalità | + | When the card works in master mode allows, with specila command, tell if the slave connected is a QEM. If so also determines the pattern of slave connected. This allows a diagnostic on the correct network configuration. You cannot extend this control to all types of existing slaves because the protocol does not provide |
- | Il comando | + | The READSTYPE |
- | slave una richiesta modbus | + | For the MODBUS |
- | letto nel parametro | + | |
- | slave è connesso ma non è possibile identificarlo.\\ | + | |
- | Per il device | + | |
- | senso vedere il manuale | + | |
- | Esempio d' | + | Example of slave identification |
<code QCL> | <code QCL> | ||
modbus: | modbus: | ||
Line 328: | Line 310: | ||
ENDIF | ENDIF | ||
</ | </ | ||
- | ==== - Estensione del protocollo | + | ==== - Protocol extension |
- | Il protocollo di comunicazione | + | The modbus standard |
* INPUT STATUS, | * INPUT STATUS, | ||
* COIL STATUS, | * COIL STATUS, | ||
* INPUT REGISTER, | * INPUT REGISTER, | ||
* HOLDING REGISTER. | * HOLDING REGISTER. | ||
- | Questi | + | These 4 types treat signals as Digital Inputs, Digital Outputs, Analog Inputs, and Analog Outputs. |
- | (sia INPUT REGISTERS | + | To allow support for datatypes larger than 16 bit, has been designed an extension to the protocol to treat long 32 bit dimension values. Implementing this feature preserves the formatting of the message |
- | (esempio | + | |
- | Per permettere di suppportare tipi di dato di dimensione maggiore di 16 bit, è stata progettata una estensione al protocollo | + | |
- | per trattare valori di dimensione | + | |
- | messaggio | + | |
- | questa estensione è attiva | + | |
- | per ogni richiesta di registro. Se l’indirizzo è superiore a 5000 verrà risposto con valore | + | |
- | rimane invariato con risposta a 16 bit. | + | |
- | ==== - Comandi e parametri | + | ==== - Commands and parameters |
- | === - Simbologia adottata | + | === - Used symbols |
- | Il nome del parametro, stato o comando viene riportato alla sinistra della tabella. | + | |
+ | The parameter name, condition or command is taken back to the left side of the table. | ||
**R**\\ | **R**\\ | ||
- | Indica se il relativo parametro o stato è ritentivo | + | Indicates if the parameter or state is retentive |
- | Se il device | + | If the device |
- | R = Ritentivo\\ | + | R = Retentive\\ |
- | 0 = Al momento dell’inizializzazione del device | + | 0 = Upon initialization of the device |
- | 1 = Al momento dell’inizializzazione del device | + | 1 = Upon initialization of the device |
- | - = Al momento dell’inizializzazione del device | + | - = Upon initialization of the device |
**D**\\ | **D**\\ | ||
- | Indica la dimensione del parametro.\\ | + | Indicates the size of the parameter.\\ |
F = Flag\\ | F = Flag\\ | ||
B = Byte\\ | B = Byte\\ | ||
Line 366: | Line 342: | ||
S = Single Float | S = Single Float | ||
- | == Condizioni | + | == Conditions |
- | Vengono descritte tutte le condizioni necessarie affinché il parametro sia considerato corretto o perché il comando venga accettato.\\ | + | |
- | In alcuni casi vengono specificati dei valori limite per l’accettazione del parametro: se vengono introdotti dei valori esterni | + | Describes all the conditions necessary for the parameter so that the parameter is considered correct or because the command is accepted.\\ |
- | ai limiti impostati, il dato viene comunque accettato; pertanto devono essere previsti opportuni controlli dell’applicativo tali | + | In some cases, limit values are specified for the acceptance of the parameter: if any values outside the limits set are introduced, the data is however accepted; therefore appropriate controls of the application must be provided to ensure the proper functioning.\\ |
- | da garantire il corretto funzionamento.\\ | + | To execute a command, all conditions must be met; otherwise the command does not execute. |
- | Per l’esecuzione di un comando, tutte le relative condizioni devono necessariamente essere soddisfatte; in caso contrario | + | |
- | il comando non viene eseguito. | + | |
**A**\\ | **A**\\ | ||
- | Indica la modalità di accesso.\\ | + | Indicates the access mode.\\ |
- | R = Read (lettura).\\ | + | R = Read.\\ |
- | W = Write (scrittura).\\ | + | W = Write.\\ |
RW = Read / Write.\\ | RW = Read / Write.\\ | ||
- | === - Parametri | + | === - Parameters |
- | ^ Nome ^ D ^ R ^ A ^ Condizioni | + | |
- | | mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Definisce se la scheda deve funzionare come master | + | ^ Name ^ D ^ R ^ A ^ Conditions |
- | | prot | B | R | R/W | - | **Protocol**\\ (0 ÷ 1)\\ Definisce il tipo di protocollo Modbus da utilizzare.\\ **0** = ASCII,\\ **1** = RTU,\\ **2** = TCPIP | | + | | mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Defines if the board should function as a master |
- | | wider | B | R | R/W | - | **Wide Registers**\\ (0 ÷ 1)\\ Indica se utilizzare l’estensione del protocollo per i registri a 32bit. Vedere capitolo | + | | prot | B | R | R/W | - | **Protocol**\\ (0 ÷ 1)\\ Defines the type of modbus protocol to use.\\ **0** = ASCII,\\ **1** = RTU,\\ **2** = TCPIP | |
- | | idcard | + | | wider | B | R | R/W | - | **Wide Registers**\\ (0 ÷ 1)\\ Indicates if to use the 32-bit registers protocol extension. See the “Extension of the Protocol” section |
- | | type | B | 1 | R/W | - | **Type**\\ | + | | idcard |
- | | addr | L | 1 | R/W | - | **Address**\\ (1 ÷ 65535)\\ | + | | type | B | 1 | R/W | - | **Type**\\ |
- | | tabreg | + | | addr | L | 1 | R/W | - | **Address**\\ (1 ÷ 65535)\\ |
- | | num | W | 1 | R/W | - | **Number**\\ (1 ÷ 512)\\ | + | | tabreg |
- | | brate | L | R | R/W | - | **Baud rate**\\ Baud rate della seriale.\\ Valori validi: 4800, 9600, 19200, 38400, 57600, 115200. | + | | num | W | 1 | R/W | - | **Number**\\ (1 ÷ 512)\\ |
- | | stopb | B | R | R/W | - | **Stop bit**\\ | + | | brate | L | R | R/W | - | **Baud rate**\\ |
- | | par | B | R | R/W | - | **Parity**\\ (0 ÷ 2)\\ **0** = none (nessuna),\\ **1** = odd (dispari),\\ **2** = even (pari). | | + | | stopb | B | R | R/W | - | **Stop bit**\\ |
- | | tout | W | R | R/W | - | **Timeout**\\ (0 ÷ 9999 msec)\\ | + | | par | B | R | R/W | - | **Parity**\\ (0 ÷ 2)\\ **0** = none,\\ **1** = odd,\\ **2** = even. | |
- | | toutsyc | + | | tout | W | R | R/W | - | **Timeout**\\ (0 ÷ 9999 msec)\\ |
+ | | toutsyc | ||
| iword1÷32 | | iword1÷32 | ||
- | | st_ibit0÷15 | + | | st_ibit0÷15 |
| ilong1÷16 | | ilong1÷16 | ||
| oword1÷32 | | oword1÷32 | ||
- | | st_obit0÷15 | + | | st_obit0÷15 |
| olong1÷16 | | olong1÷16 | ||
- | La possibilità di comunicare con il protocollo | + | The ability to communicate with the TCPIP protocol It was developed at a later time than the birth of the MODBUS |
- | Per configurare il numero della porta TCPIP è necessario andare a scrivere sui parametri | + | To configure the TCPIP port number You must go and write about the // |
* **stopb** = tcpip_port / & | * **stopb** = tcpip_port / & | ||
* **par** = tcpip_port ANDB & | * **par** = tcpip_port ANDB & | ||
- | Per impostare lo slave TCPIP a cui si vuole eseguire la richiesta è necessario andare a scrivere sul parametro | + | To set the TCPIP slave to which you want to execute the request you must go to write on the// |
- | Un indirizzo | + | An IP address can be expressed as TcpAddr3.TcpAddr2.TcpAddr1.TcpAddr0 (for example |
* **brate** = (TcpAddr3 * & | * **brate** = (TcpAddr3 * & | ||
- | === - Variabili | + | === - Variables |
- | ^ Nome ^ D ^ R ^ A ^ Condizioni | + | |
- | | err | B | 0 | R | - | **Errors**\\ | + | ^ Name ^ D ^ R ^ A ^ Conditions |
- | | serr | B | 0 | R/W | - | **Serial Errors**\\ | + | | err | B | 0 | R | - | **Errors**\\ |
- | | stype | W | 0 | R | - | **Slave type**\\ | + | | serr | B | 0 | R/W | - | **Serial Errors**\\ |
+ | | stype | W | 0 | R | - | **Slave type**\\ | ||
+ | |||
+ | |||
+ | === - States === | ||
+ | ^Name^D^R^A^Conditions^Description^ | ||
+ | |st_sended|F|0|R|-|**Sended**\\ State only been used in master mode. Activation indicates completion of the transmission of a message. The state is reset with the SEND or SENDSYC commands.| | ||
+ | |st_opencom|F|0|R|-|**Open communication port**\\ Activation indicates that the device is working the serial communications port. To set this state use the OPENCOM command, to reset CLOSECOM.| | ||
+ | |wdata|F|0|R|-|**Warning Data**\\ This bit indicates that an attempt was made to insert an invalid value in a parameter.| | ||
+ | |wcmd|F|0|R|-|**Warning Command**\\ This bit indicates that it did not execute a command because they missing the necessary conditions.| | ||
- | === - Stati === | + | === - Commands |
- | ^Nome^D^R^A^Condizioni^Descrizione^ | + | |
- | |st_sended|F|0|R|-|**Sended**\\ Stato utilizzato solo in modalità master. L’attivazione indica il completamento della trasmissione di un messaggio. Lo stato viene resettato con i comandi SEND o SENDSYC.| | + | |
- | |st_opencom|F|0|R|-|**Open communication port**\\ L' | + | |
- | |wdata|F|0|R|-|**Warning Data**\\ Questo bit segnala che è stato tentato un inserimento di un valore non valido in un parametro.| | + | |
- | |wcmd|F|0|R|-|**Warning Command**\\ Questo bit segnala che è non è stato eseguito un comando perché mancano le condizioni necessarie.| | + | |
- | === - Comandi === | + | The available commands to manage the device |
- | I comandi a disposizione per gestire il device | + | The device |
- | Il device | + | For example if the device |
- | Per esempio se il device | + | |
- | ^Nome^D^R^A^Condizioni^Descrizione^ | + | ^Name^D^R^A^Conditions^Description^ |
- | |SEND|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Sended**\\ | + | |SEND|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Sended**\\ |
- | |SENDSYC|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Send synchronize**\\ | + | |SENDSYC|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Send synchronize**\\ |
- | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read slave type**\\ | + | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read slave type**\\ |
- | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ | + | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ |
- | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ | + | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ |
- | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ | + | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ |
- | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ | + | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ |
- | ===== - Descrizione funzionamento come slave ===== | + | ===== - Slave operation description |
- | ==== - Modo di funzionamento SLAVE ==== | + | ==== - Slave mode operation |
- | La modalità slave viene impostata con il parametro | + | Slave mode is set with the mode = 1 or mode = 2 parameter. You must to introduce in the parameters the slave ID code through the idcard |
- | **Impostazioni modbus e apertura del canale di comunicazione di tipo seriale** | + | **Modbus settings and opening channel of serial communication** |
<code QCL> | <code QCL> | ||
modbus.mode = 1 ; modbus slave | modbus.mode = 1 ; modbus slave | ||
Line 462: | Line 440: | ||
ENDIF | ENDIF | ||
</ | </ | ||
- | **Impostazioni modbus e apertura del canale di comunicazione di tipo TCPIP** | + | **Modbus settings and open of the communication channel of TCPIP type** |
<code QCL> | <code QCL> | ||
modbus.mode = 1 ; modbus slave | modbus.mode = 1 ; modbus slave | ||
Line 479: | Line 457: | ||
</ | </ | ||
- | Le operazioni che spettano all’applicativo | + | The operations that should execute the QCL are essentially two: |
- | * aggiornare i parametri tipo owordNN, olongNN (che verranno poi letti dal master) | + | * update the parameters |
- | * processare i parametri tipo iwordNN, ilongNN (che sono stati scritti dal master) | + | * process the parameters |
- | === - Aggiornamento dei parametri tipo owordNN === | + | === - Updating |
- | Per aggiornare i parametri tipo owordNN il QCL deve scrivere i valori nei parametri quindi inviare il comando VALIDATE. | + | |
- | L’utilizzo del comando si rende necessario per rendere disponibili alle letture del master i nuovi dati nello stesso istante, | + | |
- | evitando così che possano venire letti solamente parte dei parametri aggiornati. Quindi l’assegnazione di un valore ad un | + | |
- | parametro device NON SIGNIFICA che esso sia immediatamente disponibile per le letture del master. Sarà disponibile | + | |
- | solamente dopo il comando VALIDATE. | + | |
- | **Esempio** | + | To update the owordNN parameters type the QCL must write values in the parameters then send the VALIDATE command. The use of the command is necessary to make available on the readings of the master the new data at the same time, so that they can be read only part of updated parameters. So assigning a value to a device parameter DOES NOT MEAN that it is immediately available for the master readings. Will only be available after the VALIDATE command. |
+ | |||
+ | **Example** | ||
<code QCL> | <code QCL> | ||
modbus.olong1 = anpos.speed | modbus.olong1 = anpos.speed | ||
Line 499: | Line 474: | ||
</ | </ | ||
- | === - Processo dei parametri tipo iwordNN === | + | === - Process |
- | Per processare i parametri tipo iwordNN, invece, il QCL deve attendere che lo stato st_msgrx venga attivato. Questo significa | + | |
- | che un messaggio di scrittura è stato inviato dal master. Per i messaggi di lettura nessun segnale viene riferito ai | + | |
- | parametri QCL. Il QCL poi deve prelevare i valori dall’area scambio dati e al termine deve inviare il comando RECEIVED, | + | |
- | solo allora lo stato st_msgrx viene disattivato. | + | |
- | **Esempio** | + | To process the iwordNN parameters type, instead,the QCL must wait for the st_msgrx state is activated. This means that a write message was sent by the master. For the read message no signal reportedly to QCL parameters. The QCL then must take the values from the data exchange and at the end needs to send the RECEIVED command, only then the st_msgrx state is disabled. |
+ | |||
+ | **Example** | ||
<code QCL> | <code QCL> | ||
WAIT modbus.st_msgrx | WAIT modbus.st_msgrx | ||
Line 513: | Line 486: | ||
RECEIVED modbus | RECEIVED modbus | ||
</ | </ | ||
- | Naturalmente non esiste nessun controllo per evitare che durante la lettura dei parametri //iwordNN// il master erroneamente | ||
- | esegua un’altra scrittura, prima che il codice del progetto presente nello slave finisca il processo.\\ | ||
- | Inoltre il codice per la manipolazione del device modbus nell’applicativo è consigliato che sia raccolto in un unico task in | ||
- | modo da non creare accessi contemporanei ai device che potrebbero generare delle condizioni non valide in ogni singolo | ||
- | contesto. | ||
- | Tutte le richieste di lettura che arrivano dal master MODBUS | + | There is no control to prevent when reading //iwordNN// parameters the master incorrectly execute another writing, before the project code present in the slave to finish the process.\\ |
- | alla stessa | + | Also the code for handling the modbus device in the application it is recommended that it is collected in a single task in order not to create simultaneous accesses to the device that could generate invalid conditions. |
- | Tutte le richieste di scrittura che arrivano dal master | + | |
- | alla stessa | + | All read requests that arrive from the master MODBUS |
+ | All write requests arriving from the MODBUS | ||
==== - Schema a blocchi ==== | ==== - Schema a blocchi ==== | ||
{{: | {{: |