Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:software:devices:modbus [2016/12/23 16:06] – [5.10.2. Parameters] qem103 | en:software:devices:modbus [2016/12/23 16:38] – [5.10.5. Comandi] qem103 | ||
---|---|---|---|
Line 387: | Line 387: | ||
- | === - Variabili | + | === - Variables |
- | ^ Nome ^ D ^ R ^ A ^ Condizioni | + | |
- | | err | B | 0 | R | - | **Errors**\\ Indica se sono stati riscontrati errori nel protocollo.\\ In modalità master il parametro viene aggiornato in coincidenza dell’attivazione dello stato // | + | |
- | | serr | B | 0 | R/W | - | **Serial Errors**\\ Indica se sono stati riscontrati errori nella comunicazione seriale. Il parametro viene aggiornato ad ogni errore rilevato. Il valore permane fino:\\ - ad un successivo errore;\\ - alla scrittura di uno dei seguenti parametri: mode, prot, wider, brate, stopb, par;\\ - ad una scrittura sullo stesso (qualsiasi valore lo azzera).\\ **0** = nessun errore,\\ **1** = parity error,\\ **2** = framing error,\\ **3** = overrun error. | + | |
- | | stype | W | 0 | R | - | **Slave type**\\ Indica il tipo di slave connesso. Il parametro viene aggiornato quando il parametro // | + | |
+ | ^ Name ^ D ^ R ^ A ^ Conditions | ||
+ | | err | B | 0 | R | - | **Errors**\\ Indicates if errors occurred in the protocol.\\ In master mode the parameter is updated to coincide the activation of the // | ||
+ | | serr | B | 0 | R/W | - | **Serial Errors**\\ Indicates if errors occurred in serial communication. The parameter is updated for each error encountered. The value persists until:\\ - under a subsequent error;\\ - the writing of one of the following parameters: mode, prot, wider, brate, stopb, par;\\ - writing about himself (any value will reset).\\ **0** = no errors,\\ **1** = parity error,\\ **2** = framing error,\\ **3** = overrun error. | ||
+ | | stype | W | 0 | R | - | **Slave type**\\ Indicates the type of slave connected. The parameter is updated when the // | ||
- | === - Stati === | ||
- | ^Nome^D^R^A^Condizioni^Descrizione^ | ||
- | |st_sended|F|0|R|-|**Sended**\\ Stato utilizzato solo in modalità master. L’attivazione indica il completamento della trasmissione di un messaggio. Lo stato viene resettato con i comandi SEND o SENDSYC.| | ||
- | |st_opencom|F|0|R|-|**Open communication port**\\ L' | ||
- | |wdata|F|0|R|-|**Warning Data**\\ Questo bit segnala che è stato tentato un inserimento di un valore non valido in un parametro.| | ||
- | |wcmd|F|0|R|-|**Warning Command**\\ Questo bit segnala che è non è stato eseguito un comando perché mancano le condizioni necessarie.| | ||
- | === - Comandi | + | === - States |
- | I comandi a disposizione per gestire il device sono elencati sotto in ordine di priorità decrescente.\\ | + | |
- | Il device esegue tutti i comandi ricevuti entro lo stesso tempo di campionamento iniziando da quello con la priorità maggiore.\\ | + | |
- | Per esempio se il device riceve nello stesso tempo di campionamento i comandi CLOSECOM e OPENCOM, per primo esegue il comando OPENCOM e poi quello di CLOSECOM lasciando perciò la porta di comunicazione chiusa. | + | |
- | ^Nome^D^R^A^Condizioni^Descrizione^ | + | ^Name^D^R^A^Conditions^Description^ |
- | |SEND|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Sended**\\ | + | |st_sended|F|0|R|-|**Sended**\\ State only been used in master mode. Activation indicates completion of the transmission of a message. The state is reset with the SEND or SENDSYC commands.| |
- | |SENDSYC|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Send synchronize**\\ | + | |st_opencom|F|0|R|-|**Open communication port**\\ Activation indicates that the device is working the serial communications port. To set this state use the OPENCOM command, to reset CLOSECOM.| |
- | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read slave type**\\ | + | |wdata|F|0|R|-|**Warning Data**\\ This bit indicates that an attempt was made to insert an invalid value in a parameter.| |
- | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ | + | |wcmd|F|0|R|-|**Warning Command**\\ This bit indicates that it did not execute a command because they missing the necessary conditions.| |
- | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ | + | |
- | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ | + | === - Commands === |
- | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ | + | |
+ | The available commands to manage the device are listed below in descending order of priority.\\ | ||
+ | The device executes all commands received within the same sampling time starting from the one with the highest priority.\\ | ||
+ | For example if the device receives the same sampling time CLOSECOM and OPENCOM commands, first run the OPENCOM command and then to CLOSECOM leaving therefore the communication port closed. | ||
+ | |||
+ | ^Name^D^R^A^Conditions^Description^ | ||
+ | |SEND|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Sended**\\ | ||
+ | |SENDSYC|-|-|-|mode = 0\\ 0 < num <= 128\\ st_sended = 1\\ st_opencom = 1|**Send synchronize**\\ | ||
+ | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read slave type**\\ | ||
+ | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ | ||
+ | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ | ||
+ | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ | ||
+ | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ | ||