Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:software:devices:modbus [2016/12/23 16:25] – [5.10.3. Variabili] qem103 | en:software:devices:modbus [2016/12/23 16:39] – [6. Descrizione funzionamento come slave] qem103 | ||
---|---|---|---|
Line 395: | Line 395: | ||
- | === - Stati === | + | === - States |
- | ^Nome^D^R^A^Condizioni^Descrizione^ | + | |
- | |st_sended|F|0|R|-|**Sended**\\ Stato utilizzato solo in modalità master. L’attivazione indica il completamento della trasmissione di un messaggio. Lo stato viene resettato con i comandi SEND o SENDSYC.| | + | |
- | |st_opencom|F|0|R|-|**Open communication port**\\ L' | + | |
- | |wdata|F|0|R|-|**Warning Data**\\ Questo bit segnala che è stato tentato un inserimento di un valore non valido in un parametro.| | + | |
- | |wcmd|F|0|R|-|**Warning Command**\\ Questo bit segnala che è non è stato eseguito un comando perché mancano le condizioni necessarie.| | + | |
- | === - Comandi === | + | ^Name^D^R^A^Conditions^Description^ |
- | I comandi a disposizione per gestire il device sono elencati sotto in ordine di priorità decrescente.\\ | + | |st_sended|F|0|R|-|**Sended**\\ State only been used in master mode. Activation indicates completion of the transmission of a message. The state is reset with the SEND or SENDSYC commands.| |
- | Il device esegue tutti i comandi ricevuti entro lo stesso tempo di campionamento iniziando da quello con la priorità maggiore.\\ | + | |st_opencom|F|0|R|-|**Open communication port**\\ Activation indicates that the device |
- | Per esempio se il device | + | |wdata|F|0|R|-|**Warning Data**\\ This bit indicates that an attempt was made to insert an invalid value in a parameter.| |
+ | |wcmd|F|0|R|-|**Warning Command**\\ This bit indicates that it did not execute a command because they missing the necessary conditions.| | ||
- | ^Nome^D^R^A^Condizioni^Descrizione^ | + | === - Commands |
- | |SEND|-|-|-|mode | + | |
- | |SENDSYC|-|-|-|mode | + | |
- | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read slave type**\\ Richiesta lettura informazione type sullo slave specificato in idcard. La risposta verrá segnalata sul parametro stype quando lo stato st_sended diventa 1.| | + | |
- | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ Azzera la segnalazione del parametro wdata.| | + | |
- | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ Azzera la segnalazione del parametro wcmd.| | + | |
- | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ Apre la comunicazione seriale (il device quindi impegna la porta di comunicazione ). Lo stato st_opencom diventa 1.| | + | |
- | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ Chiude la comunicazione seriale (il device quindi non impegna piú la porta di comunicazione ). Lo stato st_opencom diventa 0.| | + | |
+ | The available commands to manage the device are listed below in descending order of priority.\\ | ||
+ | The device executes all commands received within the same sampling time starting from the one with the highest priority.\\ | ||
+ | For example if the device receives the same sampling time CLOSECOM and OPENCOM commands, first run the OPENCOM command and then to CLOSECOM leaving therefore the communication port closed. | ||
- | ===== - Descrizione funzionamento come slave ===== | + | ^Name^D^R^A^Conditions^Description^ |
+ | |SEND|-|-|-|mode | ||
+ | |SENDSYC|-|-|-|mode | ||
+ | |READSTYPE|-|-|-|mode = 0\\ st_sended = 1\\ st_opencom = 1|**Read | ||
+ | |CLRWDATA|-|-|-|-|**Clear Warning Data**\\ Reset the wdata parameter reporting.| | ||
+ | |CLRWCMD|-|-|-|-|**Clear Warning Command**\\ Reset the wcmd parameter reporting.| | ||
+ | |OPENCOM|-|-|-|st_opencom = 0|**Open Serial communication**\ Open the serial communication (the device then committed the communications port ). The st_opencom status becomes 1.| | ||
+ | |CLOSECOM|-|-|-|-|**Close Serial communication**\\ Close the serial communication (the device then does not committted the communications port ). The st_opencom status becomes 0.| | ||
+ | |||
+ | |||
+ | ===== - Slave operation description | ||
==== - Modo di funzionamento SLAVE ==== | ==== - Modo di funzionamento SLAVE ==== | ||