Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:software:devices:modbus [2016/12/23 17:04] – [6.1.2. Processo dei parametri tipo iwordNN] qem103 | en:software:devices:modbus [2016/12/23 17:23] – [6.3.2. Parametri] qem103 | ||
---|---|---|---|
Line 492: | Line 492: | ||
All read requests that arrive from the master MODBUS refer to the //owordNN// type data by accessing to the same data area. The slave provides the values that the master will read in the //owordNN// parameters type.\\ | All read requests that arrive from the master MODBUS refer to the //owordNN// type data by accessing to the same data area. The slave provides the values that the master will read in the //owordNN// parameters type.\\ | ||
All write requests arriving from the MODBUS master refer to the //iwordNN// type data aby accessing to the same data area. The slave provides the //iwordNN// parameters where the master will write data. | All write requests arriving from the MODBUS master refer to the //iwordNN// type data aby accessing to the same data area. The slave provides the //iwordNN// parameters where the master will write data. | ||
- | ==== - Schema a blocchi | + | ==== - Block diagram |
{{: | {{: | ||
- | ==== - Comandi e parametri | + | ==== - Commands and parameters |
- | === - Simbologia adottata | + | === - Used symbols |
- | Il nome del parametro, stato o comando è riportato alla sinistra della tabella. | + | The parameter name, condition or command is shown at the left of the table. |
**R**\\ | **R**\\ | ||
- | Indica se il relativo parametro o stato è ritentivo | + | Indicates if the parameter or state is retentive |
- | Se il device | + | If the device |
- | R = Ritentivo\\ | + | R = Retentive\\ |
- | 0 = Al momento dell’inizializzazione del device | + | 0 = Upon initialization of the device |
- | 1 = Al momento dell’inizializzazione del device | + | 1 = Upon initialization of the device |
- | - = Al momento dell’inizializzazione del device | + | - = Upon initialization of the device |
**D**\\ | **D**\\ | ||
- | Indica la dimensione del parametro.\\ | + | Indicates the size of the parameter.\\ |
F = Flag\\ | F = Flag\\ | ||
B = Byte\\ | B = Byte\\ | ||
Line 517: | Line 518: | ||
S = Single Float\\ | S = Single Float\\ | ||
- | == Condizioni | + | == Conditions |
- | Sono descritte tutte le condizioni necessarie affinché il parametro sia considerato corretto o perché il comando venga accettato.\\ | + | |
- | In alcuni casi sono specificati dei valori limite per l’accettazione del parametro: se sono introdotti dei valori esterni ai limiti impostati, il dato è comunque accettato; pertanto devono essere previsti opportuni controlli dell’applicativo tali da garantire il corretto funzionamento.\\ Per l’esecuzione di un comando, tutte le relative condizioni devono necessariamente essere soddisfatte; in caso contrario il comando non è eseguito. | + | Describes all the conditions necessary so that the parameter is considered correct or because the command is accepted.\\ |
+ | In some cases, limit values are specified for the acceptance of the parameter: if there are any values outside the limits set, the data is however accepted; therefore appropriate controls of the application must be provided to ensure the proper functioning.\\ To execute a command, all conditions must be met; otherwise the command is not executed. | ||
**A**\\ | **A**\\ | ||
- | Indica la modalità d' | + | Indicates the access mode.\\ |
- | R = Read (lettura).\\ | + | R = Read.\\ |
- | W = Write (scrittura).\\ | + | W = Write.\\ |
RW = Read / Write. | RW = Read / Write. | ||
- | === - Parametri | + | === - Parameters |
+ | FIXME | ||
^ Nome ^ D ^ R ^ A ^ Condizioni | ^ Nome ^ D ^ R ^ A ^ Condizioni | ||
| mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Definisce se la scheda deve funzionare come master o come slave.\\ **1** = slave con area di scambio dati fissa;\\ **2** = slave senza area di scambio dati fissa: ad ogni scrittura o lettura eseguita dal master viene messi a 1 il flag st_msgrx.\\ Contemporaneamente i parametri //type//, //addr// e //num// indicano le caratteristiche del messaggio ricevuto.\\ - **Type** indica il tipo di funzione che vuole fare ill master (lettura o scrittura), | | mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Definisce se la scheda deve funzionare come master o come slave.\\ **1** = slave con area di scambio dati fissa;\\ **2** = slave senza area di scambio dati fissa: ad ogni scrittura o lettura eseguita dal master viene messi a 1 il flag st_msgrx.\\ Contemporaneamente i parametri //type//, //addr// e //num// indicano le caratteristiche del messaggio ricevuto.\\ - **Type** indica il tipo di funzione che vuole fare ill master (lettura o scrittura), |