Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
en:software:devices:modbus [2016/12/23 17:04] – [6.1.2. Processo dei parametri tipo iwordNN] qem103 | en:software:devices:modbus [2016/12/27 14:47] – [6.3.5. Comandi] qem103 | ||
---|---|---|---|
Line 492: | Line 492: | ||
All read requests that arrive from the master MODBUS refer to the //owordNN// type data by accessing to the same data area. The slave provides the values that the master will read in the //owordNN// parameters type.\\ | All read requests that arrive from the master MODBUS refer to the //owordNN// type data by accessing to the same data area. The slave provides the values that the master will read in the //owordNN// parameters type.\\ | ||
All write requests arriving from the MODBUS master refer to the //iwordNN// type data aby accessing to the same data area. The slave provides the //iwordNN// parameters where the master will write data. | All write requests arriving from the MODBUS master refer to the //iwordNN// type data aby accessing to the same data area. The slave provides the //iwordNN// parameters where the master will write data. | ||
- | ==== - Schema a blocchi | + | ==== - Block diagram |
{{: | {{: | ||
- | ==== - Comandi e parametri | + | ==== - Commands and parameters |
- | === - Simbologia adottata | + | === - Used symbols |
- | Il nome del parametro, stato o comando è riportato alla sinistra della tabella. | + | The parameter name, condition or command is shown at the left of the table. |
**R**\\ | **R**\\ | ||
- | Indica se il relativo parametro o stato è ritentivo | + | Indicates if the parameter or state is retentive |
- | Se il device | + | If the device |
- | R = Ritentivo\\ | + | R = Retentive\\ |
- | 0 = Al momento dell’inizializzazione del device | + | 0 = Upon initialization of the device |
- | 1 = Al momento dell’inizializzazione del device | + | 1 = Upon initialization of the device |
- | - = Al momento dell’inizializzazione del device | + | - = Upon initialization of the device |
**D**\\ | **D**\\ | ||
- | Indica la dimensione del parametro.\\ | + | Indicates the size of the parameter.\\ |
F = Flag\\ | F = Flag\\ | ||
B = Byte\\ | B = Byte\\ | ||
Line 517: | Line 518: | ||
S = Single Float\\ | S = Single Float\\ | ||
- | == Condizioni | + | == Conditions |
- | Sono descritte tutte le condizioni necessarie affinché il parametro sia considerato corretto o perché il comando venga accettato.\\ | + | |
- | In alcuni casi sono specificati dei valori limite per l’accettazione del parametro: se sono introdotti dei valori esterni ai limiti impostati, il dato è comunque accettato; pertanto devono essere previsti opportuni controlli dell’applicativo tali da garantire il corretto funzionamento.\\ Per l’esecuzione di un comando, tutte le relative condizioni devono necessariamente essere soddisfatte; in caso contrario il comando non è eseguito. | + | Describes all the conditions necessary so that the parameter is considered correct or because the command is accepted.\\ |
+ | In some cases, limit values are specified for the acceptance of the parameter: if there are any values outside the limits set, the data is however accepted; therefore appropriate controls of the application must be provided to ensure the proper functioning.\\ To execute a command, all conditions must be met; otherwise the command is not executed. | ||
**A**\\ | **A**\\ | ||
- | Indica la modalità d' | + | Indicates the access mode.\\ |
- | R = Read (lettura).\\ | + | R = Read.\\ |
- | W = Write (scrittura).\\ | + | W = Write.\\ |
RW = Read / Write. | RW = Read / Write. | ||
- | === - Parametri | + | === - Parameters |
- | ^ Nome ^ D ^ R ^ A ^ Condizioni | + | |
- | | mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Definisce se la scheda deve funzionare come master | + | ^ Name ^ D ^ R ^ A ^ Conditions |
- | | prot | B | R | R/W | - | **Protocol**\\ | + | | mode | B | R | R/W | - | **Mode**\\ (0 ÷ 2)\\ Defines if the board should function as a master |
- | | wider | B | R | R/W | - | **Wide Registers**\\ | + | | prot | B | R | R/W | - | **Protocol**\\ |
- | | idcard | + | | wider | B | R | R/W | - | **Wide Registers**\\ |
- | | brate | L | R | R/W | - | **Baud rate**\\ Baud rate della seriale.\\ Valori validi: 4800, 9600, 19200, 38400, 57600, 115200. | + | | idcard |
- | | stopb | B | R | R/W | - | **Stop bit**\\ | + | | brate | L | R | R/W | - | **Baud rate**\\ Baud rate of the serial.\\ Valid values: 4800, 9600, 19200, 38400, 57600, 115200. |
+ | | stopb | B | R | R/W | - | **Stop bit**\\ | ||
| par | B | R | R/W | - | **Parity**\\ (0 ÷ 2)\\ **0** = none,\\ **1** = even,\\ **2** = odd. | | | par | B | R | R/W | - | **Parity**\\ (0 ÷ 2)\\ **0** = none,\\ **1** = even,\\ **2** = odd. | | ||
- | | rdelay | + | | rdelay |
| iword1÷32 | | iword1÷32 | ||
- | | st_ibit0÷15 | + | | st_ibit0÷15 |
| ilong1÷16 | | ilong1÷16 | ||
| oword1÷32 | | oword1÷32 | ||
- | | st_obit0÷15 | + | | st_obit0÷15 |
| olong1÷16 | | olong1÷16 | ||
Line 547: | Line 550: | ||
- | === - Variabili | + | === - Variables |
- | ^Nome^D^R^A^Condizioni^ Descrizione^ | + | |
- | |serr|B|0|R/ | + | ^Name^D^R^A^Conditions^Description^ |
+ | |serr|B|0|R/ | ||
+ | |||
+ | === - States === | ||
+ | |||
+ | ^Name^D^R^A^Conditions^Description^ | ||
+ | |st_msgrx|F|0|R|-|**Message received**\\ State used only in slave mode. Indicates that a message from the master has executed a write in the QCL data exchange area. The state is reset with the RECEIVED command.| | ||
+ | |st_opencom|F|0|R|-|**Open communication port**\\ Activation indicates that the device is working with the serial communications port. To set this state use the OPENCOM command, for reset use CLOSECOM.| | ||
+ | |wdata|F|0|R|-|**Warning Data**\\ This bit indicates that an attempt was made to insert an invalid value in a parameter.| | ||
+ | |wcmd|F|0|R|-|**Warning Command**\\ This bit indicates that it did not execute a command because they lack the necessary conditions.| | ||
+ | |||
+ | === - Commands === | ||
- | === - Stati === | + | The available commands to manage the device are listed below in descending order of priority.\\ |
- | ^Nome^D^R^A^Condizioni^ Descrizione^ | + | The device executes all commands |
- | |st_msgrx|F|0|R||-|**Message | + | For example if the device |
- | |st_opencom|F|0|R|-|**Open communication port**\\ L' | + | |
- | |wdata|F|0|R|-|**Warning Data**\\ Questo bit segnala che è stato tentato un inserimento di un valore non valido in un parametro.| | + | |
- | |wcmd|F|0|R|-|**Warning Command**\\ Questo bit segnala che è non è stato eseguito un comando perchè mancano le condizioni necessarie.| | + | |
- | === - Comandi === | + | ^ Name ^ D ^ R ^ A ^ Conditions |
- | I comandi a disposizione per gestire il device sono elencati sotto in ordine di priorità decrescente.\\ | + | | RECEIVED |
- | Il device esegue tutti i comandi ricevuti entro lo stesso tempo di campionamento iniziando da quello con la priorità maggiore.\\ | + | | VALIDATE |
- | Per esempio se il device riceve nello stesso tempo di campionamento i comandi CLOSECOM e OPENCOM, per primo esegue il comando OPENCOM e poi quello di CLOSECOM lasciando perciò la porta di comunicazione chiusa. | + | | CLRWDATA |
- | ^ Nome ^ D ^ R ^ A ^ Condizioni | + | | CLRWCMD |
- | | RECEIVED | + | | OPENCOM |
- | | VALIDATE | + | | CLOSECOM |
- | | CLRWDATA | + | |
- | | CLRWCMD | + | |
- | | OPENCOM | + | |
- | | CLOSECOM | + | |