Differences

This shows you the differences between two versions of the page.

--- en:strumenti:qmoveplus:c1r44:p1r44f-001:mdo_p1r44f-009 [2022/12/14 14:00] – [Table] qem215
+++ en:strumenti:qmoveplus:c1r44:p1r44f-001:mdo_p1r44f-009 [2022/12/23 15:49] (current) – [Belt] qem215
@@ Line 11: / Line 11: @@
 ^ Editor:                                            | Andrea Zarantonello                                                                                          |||
 ^ Approver                                           | Giuliano Tognon                                                                                              |||
-^ Link:                                              | http://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/c1r44/p1r44f-001/mdo_p1r44f-009                       |||
+^ Link:                                              | https://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/c1r44/p1r44f-001/mdo_p1r44f-009                       |||
 ^ Language:                                          | English                                                                                                      |||
 |                                                                                                                                                                  ||||
@@ Line 139: / Line 139: @@
 | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_motor_120x60_off.png?100&nolink}}          | Access to the engine test page.                                                            |
 | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_page.png?100&nolink}}                                   | Access to the belt speed setting page                                                      |
+| {{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_disable_page_button.png?100&nolink}}                     | Access to enable/disable heads page                                                        |
 | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_belt_60x60_off.png?50&nolink}}             | Forcing the movement of the conveyor belt and the conveyor rollers (only in manual mode).  |
@@ Line 217: / Line 218: @@
 Look in the [[en/strumenti:qmoveplus:c1r44:p1r44f-001:mmf_p1r44f-009|start up manual]] how to best perform the procedures.
-<html><pagebreak /></html>
+The button {{:strumenti:qmoveplus:c1r44:p1r44f-001:offset_button.png?nolink&100|}} open the page "Offset tools":
+{{:strumenti:qmoveplus:c1r44:p1r44f-001:offset_teste.png?nolink&500|}}
+In this page is possible to set a horizontal offset for every single head.\\ The button =0 reset all the offset values \\ The button "progression" associate to every head the value "progression of" + offset of the head before.
 ==== Orthogonal correction====
 Look image [[#Functioning| general view machine]]
@@ Line 420: / Line 426: @@
 In this page it is possible to set the speed of the conveyor belt. Max and min values are setted in generic parameters (PG 36  PG 37).
+If the machine is in **MANUAL** state:\\  press button {{:strumenti:qmoveplus:c1r44:p1r44f-001:pulsante_rulliere.png?nolink&50|}}  to activate O3: ROLLERS RUN, \\ press button{{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_page.png?nolink&90|}} to activate O2 "BELT RUN"
+<html><pagebreak /></html>
+===== Enable/Disable Tools =====
+{{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_disable_page_button.png?100&nolink}} -> {{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_head_page.png?nolink&400|}}
+In this page it's possible to enable or disable the tools.\\ Led on (yellow) = tool enabled\\ Led off(grey) = tool disabled
 <html><pagebreak /></html>