Differences

This shows you the differences between two versions of the page.

--- en:appnote:an017 [2015/02/16 14:57] – creata documentazione
+++ en:appnote:an017 [2019/08/29 17:01] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
+====== AN017 ======
+===== Procedure =====
+Switch off the controller power
+Insert the MMC card containing the application programs in the controller
+Press **F1 key** {{tasti:tasto_f1.png?40}} (or {{varie:pulsante_6x6.jpg?40}}**FUNC** on back) and power the controller.
+Keep the **F1 key** {{tasti:tasto_f1.png?40}} (or {{varie:pulsante_6x6.jpg?40}}**FUNC** on back) pressed until the **System Functions** screen is opened
+The Qmove application does not startup and the **"SYSTEM FUNCTIONS"** screen will open.
+The screen shows function option 01 Reset Error Checksum as shown below, it is also indicated by the **L1** led on the back of the controller\\
+(See below for the System Function options and L1-L2-L3-L4 led combinations)
+{{sezioni:funzionamento:schermata_funzioni1_01.png?nolink&400}}
+Press **F1 key** {{tasti:tasto_f1.png?40}} (or {{varie:pulsante_6x6.jpg?40}}**FUNC** on back) to change function option screens one by one.\\
+Go to the **Function Option 05 - Application upload from MMC/SD** screen (**L1-L3** led's on back)
+{{sezioni:funzionamento:schermata_funzione05_01.png?nolink&400}}
+Press **ENTER** {{tasti:tasto_f1.png?40}} (or {{varie:pulsante_6x6.jpg?40}}**BOOT** on back) for **2 seconds** to execute the function on display.
+A **PASSWORD** entry box opens - use the number keys to enter **1 2 3** and press **ENTER** {{tasti:tasto_f1.png?40}}
+ FIXME  inserisci immagine della finestra PASSWORD
+The function starts and is confirmed by the message "Executing", showing the percentage progress
+{{sezioni:funzionamento:schermata_funzione05_02.png?nolink&400}}
+|The {{led:led_lamp.jpg?20}}**pow** led will start blinking to signal the function is running.|
+|When the function is completed the {{led:led_on.jpg?20}}**pow** stops blinking.|
+The **SUCCESSFUL** message in green shown on screen
+To restart the controller press **F1 key** {{tasti:tasto_f1.png?40}} (or {{varie:pulsante_6x6.jpg?40}}**FUNC** on back)
+If there is an error the {{led:led_off.jpg?20}} **pow** stops blinking and the {{led:led_lamp.jpg?20}} **ERR** starts blinking. The screen gives a message with the **ERROR CODE** in red.
+{{sezioni:funzionamento:schermata_funzione05_03.png?nolink&400}}
+|See the **ERROR CODE** table and corresponding led's below |
+==== System Function options ====
+If the "**PWD**" column has '**Y**' the function requires a system password //(default: "123")//.
+**System Functions**
+^n.^Led ON^System Function^PWD^Description^
+|**1**|{{led:led_on.jpg?20}}L1|01 - Reset Error Checksum|  **-**  |Reset checksum error. \\ N.B.: if there is a checksum error led {{led:led_on.jpg?20}}L1 blinks.|
+|**2**|{{led:led_on.jpg?20}}L2|02 - Copy all files MMC/SD -> NAND|  **-**  |All files in the MMC/SD are copied to the NAND Flash.|
+|**3**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L2|03 - Copy all files NAND  -> MMC/SD|  **-**  |Copia All files in the NAND Flash are copied to the MMC/SD.|
+|**4**|{{led:led_on.jpg?20}}L3|04 - Application delete|  **Y**  |The application is deleted.|
+|**5**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L3|05 - Application upload from MMC/SD|  **Y**  |The application on MMC/SD is uploaded onto the controller|
+|**6**|{{led:led_on.jpg?20}}L2\\ {{led:led_on.jpg?20}}L3|06 - Set Date & Time|  **-**  |Change the date & time settings of the system clock |
+|**7**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L2\\ {{led:led_on.jpg?20}}L3|07 - Downl. retentive data to MMC/SD|  **-**  |The retentive data is saved on MMC/SD.|
+|**8**|{{led:led_on.jpg?20}}L4|08 - Set NEW Password|  **Y**  |Change the password for access to "locked" system functions|
+|**9**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L4|09 - Remove all files from NAND Flash|  **Y**  |All files in the NAND Flash are deleted.|
+|**10**|{{led:led_on.jpg?20}}L2\\ {{led:led_on.jpg?20}}L4|10 - Show NAND Flash files|  **-**  |The files stored in the NAND Flash are listed|
+|**11**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L2\\ {{led:led_on.jpg?20}}L4|11 - Touch Calibration|  **-**  |The Touchscreen calibration procedure is run.|
+|**12**|{{led:led_on.jpg?20}}L3\\ {{led:led_on.jpg?20}}L4|12 - Set Ethernet communic. parameter|  **-**  |The ethernet communication paramenter setting procedure is run (IP address,..., etc.)|
+|**13**|{{led:led_on.jpg?20}}L1\\ {{led:led_on.jpg?20}}L3\\ {{led:led_on.jpg?20}}L4|13 - Backup to NAND|  **-**  |A backup of the QCL and QTP applications and data are made in the NAND Flash.|
+|**14**|{{led:led_on.jpg?20}}L2\\ {{led:led_on.jpg?20}}L3\\ {{led:led_on.jpg?20}}L4|14 - Restore from NAND|  **Y**  |The QCL and QTP applications and data are restored from the NAND Flash.|
+//N.B. To quit System Functions press **F1** (or **FUNC** on back) for at least two seconds.//
+===== Error Messagge =====
+When a system error ends with an error, the number of Quando una funzione di sistema termina con errore, il numero di lampeggi del led {{led:led_lamp.jpg?20}} **err** led blinks a number of times to indicate the type of error.\\
+=== System Functions Error Messages ===
+^Error/ERR Led blinks^Messagge^
+|  **1**  |''Generic error''|
+|  **2**  |''Open/Exist/Create file error''|
+|  **3**  |''Read file error''|
+|  **4**  |''Write file error''|
+|  **5**  |''Out of Memory error''|
+|  **6**  |''QMos Version error''|
+|  **7**  |''Checksum Error''|
+|  **8**  |''Symbols checksum No Match''|
+|  **9**  |''Configuration / Symbols error''|
+|  **10**  |''File format error''|
+|  **11**  |''Format error''|
+|  **12**  |''Device not present or unformatted''|
+|  **13**  |''Application not present error''|
+|  **14**  |''Touch calibration failure''|
+|  **15**  |''File compression type not support''|
+|  **16**  |''Target don't match project !''|
+|  **17**  |''Fw version don't match project !''|
+|  **18**  |''File copy error''|
+|  **19**  |''File size error''|
+|  **20**  |''Crypt operation error''|
+|  **21**  |''Invalid Product Serial Number''|
+|  **22**  |''Function is locked''|
+Il numero di lampeggi indica il tipo di errore avvenuto come riportato nella tabella [[#Messaggi di errore delle Funzioni di sistema]].