en:strumenti:qmoveplus:c1r11:mdu_p1r11fe30-001:connessioni_e_setup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
en:strumenti:qmoveplus:c1r11:mdu_p1r11fe30-001:connessioni_e_setup [2019/10/31 15:38] – [CN7 - 1 counter (PP, LD) - MMB axis] qem103en:strumenti:qmoveplus:c1r11:mdu_p1r11fe30-001:connessioni_e_setup [2019/10/31 15:42] (current) – qem103
Line 1: Line 1:
 +====== P1R11FE30 - 001 : Setup and Connections ======
  
 +  * **[[#Informations|Informations]]**
 +  * **[[#Description|Description]]**
 +  * **[[#Hardware and wirings|Hardware and wirings]]**
 +  * **[[#Electric connections|Electric connections]]**
 +  * **[[#Setup|Setup]]**
 +  * **[[#Assistance|Assistance]]**
 +
 +<html><pagebreak /></html>
 +====== Informations ======
 +
 +===== Release =====
 +
 +This document is fully valid, except for errors or omissions.
 +
 +^Release^Description^Date^
 +|1.0|New manual.|06/11/13|
 +==== Specifications ====
 +
 +All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation .
 +
 +QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information provided in this document can be changed without notice. QEM shall not be held liable for any error that may appear in this document.
 +
 +Registered Trademarks:
 +
 +  * QEM® is a registered trademark.
 +  * Microsoft® and MS-DOS® are registered trademarks and Windows® is a trademark of Microsoft Corporation.
 +
 +
 +<html><pagebreak /></html>
 +======   Description ======
 +
 +The **P1R11FE30 - 001**** application, **installed on the //Qmove J1-R11-FE30, // hardware is designed to control a cookies dispensing machine with 4 axes. The salient features of the **P1R11FE30 - 001** are described below. 
 +
 +**The manual will distinguish between **__**standard**__** characteristics and **__**optional**__**.** characteristics.
 +===== Overview of the Characteristics =====
 +
 +
 +
 +
 +  *Axes MMB, MMC, MCB controlled by PID on space (brushless motors with servo drives or asynchronous motors with vector inverters).
 +  *Axis MT for the conveyor. Only encoder simulation signal is provided.
 +  *Homing functions for axes MMB, MMC, MCB.
 +  *Select the language
 +  *Modbus communication with ESA hmi panel.
 +  *Diagnostics of the inputs and the outputs.
 +  *Messagges for active faults, to assist troubleshooting.
 +  *Help Messagges.
 +  *Backup and restore of the data on non volativle memory (FLASH EPROM).
 +
 +
 +<html><pagebreak /></html>
 +====== Hardware and wirings ======
 +
 +===== C1-R11-FE30 =====
 +|{{strumenti:QmovePlus:c1R11:c1R11_3d_02.png?nolink&500|C1-R11}}|
 +|//General view of C1-R11FE30//|
 +
 +|{{strumenti:qmoveplus:c1r11:c1r11_slot2_01.png?nolink&700}}|
 +|//Rear view of SLOT2 of C1-R11FE30//|
 +
 +|{{strumenti:qmoveplus:j1p31:j1p31_1mg5f_01.png?nolink&600}}|
 +|//Rear view of SLOT3 of C1-R11FE30 - 1MG5F card//|
 +
 +===== A1-HMI-QC050 =====
 +|{{strumenti:qpanelplus:qc050:qc050_3d_01.png?nolink&500}}|
 +|//General view of A1-HMI-QC050//|
 +
 +<html><pagebreak /></html>
 +
 +===== 1MG5F card =====
 +==== Slot supply ====
 +Use an isolated power unit with 24Vdc +/-5% output conform to EN60950-1. There will be no internal fuse.
 +==== External connections ====
 +
 +  *PROG PORT -> Serial port for programmation with TTl standard logic.
 +  *USER PORT -> Multistandard serial for hmi connection (RS232, RS422, RS485)
 +  *AUX RS485 PORT -> Serial port with RS485 standard.
 +  *ETHERNET PORT -> RJ45 connection. For programmation.
 +  *CAN PORT -> "field bus" Canbus type.
 +
 +Nr. 1 MMC/SD slot for data saving/loading.
 +
 +<html><pagebreak /></html>
 +
 +==== I/O List ====
 +This section shows all I/O divided in each connector. For more detailed description, see next sections about single connector pins.
 +
 +=== Digital inputs (n. 16) ===
 +^ID^DESCRIPTION^CONNECTOR^HARDWARE|
 +|  I1  |Fault MMB driver|  CN11  |  C1R11-FE30  |
 +|  I2  |Fault MMC driver|:::|:::|
 +|  I3  |Fault MCB driver|:::|:::|
 +|  I4  |Start (1)/Stop (0) sinchronism|:::|:::|
 +|  I5  |Emergency|:::|:::|
 +|  I6  |Enabling Switch Zero MMB axis|:::|:::|
 +|  I7  |Enabling Switch Zero MMC axis|:::|:::|
 +|  I8  |Enabling Switch Zero MCB axis|:::|:::|
 +|  I9  |Manual (0) / Automatic (1) selector|  CN12  |  C1R11-FE30  |
 +|  I10  |Start Homing|:::|:::|
 +|  I11  |Jog forward selected axis|:::|:::|
 +|  I12  |Jog backward selected axis|:::|:::|
 +|  I13  |MMB axis selection for jog movements|:::|:::|
 +|  I14  |MMC axis selection for jog movements|:::|:::|
 +|  I15  |MCB axis selection for jog movements|:::|:::|
 +|  I16  |//Free//|:::|:::|
 +
 +<html><pagebreak /></html>
 +=== Digital outputs (n. 16) ===
 +
 +^ID^DESCRIPTION^CONNECTOR^HARDWARE|
 +|  O1  |Reset MMB driver|  CN15  |  C1R11-FE30  |
 +|  O2  |Reset MMC driver|:::|:::|
 +|  O3  |Reset MCB driver|:::|:::|
 +|  O4  |Cycle on signal|:::|:::|
 +|  O5  |Enable MMB driver|:::|:::|
 +|  O6  |Enable MMC driver|:::|:::|
 +|  O7  |Enable MCB driver|:::|:::|
 +|  O8  |Emergency Normally closed|:::|:::|
 +|  O9  |Emergency state lamp|  CN16  |  C1R11-FE30  |
 +|  O10  |Manual state lamp|:::|:::|
 +|  O11  |Homing done - machine ready|:::|:::|
 +|  O12  |//Free//|:::|:::|
 +|  O13  |//Free//|:::|:::|
 +|  O14  |//Free//|:::|:::|
 +|  O15  |//Free//|:::|:::|
 +|  O16  |//Free//|:::|:::|
 +
 +<html><pagebreak /></html>
 +=== Bidirectional counters (n° 4) ===
 +
 +^**ID**^**DESCRIPTION**^**CONNECTOR**^**HARDWARE**|
 +|PHA1\\ PHB1|MMB axis|  CN7  |  C1R11-FE30  |
 +|PHA2\\ PHB2|MMC axis|  CN8  |:::|
 +|PHA3\\ PHB3|MCB axis|  CN9  |:::|
 +|PHA4\\ PHB4|MT axis|  CN10  |:::|
 +
 +=== Analog inputs (n. 2) ===
 +
 +^**ID**^**DESCRIPTION **^**CONNECTOR**^**HARDWARE**|
 +|AI1|//Free//|  CN18  |  C1R11-FE30  |
 +|AI2|//Free//|:::|:::|
 +
 +=== Analog outputs (n. 4) ===
 +
 +^**ID**^**DESCRIPTION**^**CONNECTOR**^**HARDWARE**|
 +|AO1|MMB axis speed control ±10Vdc|  CN17  |  C1R11-FE30  |
 +|AO2|MMC axis speed control ±10Vdc|:::|:::|
 +|AO3|MCB axis speed control ±10Vdc|:::|:::|
 +|AO4|//Free//|:::|:::|
 +
 +<html><pagebreak /></html>
 +
 +====== Electric connections ======
 +
 +===== C1-R11-FE30 =====
 +
 +==== CN1- Power supply (Slot supply) ====
 +^Power supplies available^24 Vdc^24 Vac^
 +^Voltage range|22 ÷ 27 Vdc|+/-15%|
 +^Max. absorption|30W|35VA|
 +^Frequency| |50/60Hz|
 +
 +|  {{:connettori:cnn_3fv_p5_01.png?nolink}}  |1|AC power phase/ DC power positive|
 +|:::|2|Gnd-PE (signals)|
 +|:::|3|AC power phase/ DC power 0V|
 +
 +<html><pagebreak /></html>
 +
 +==== CN2 - PORTA USER. Multistandard serial RS232-RS422-RS485 (isolated) ====
 +Serial port used to connect hmi with MODBUS RTU (RS485).
 +NB. This port can be used also to connect wit A1-HMI-QC050 in RS422.
 +
 +|  {{:connettori:cnn_6x2fv_p3.5_01.png?nolink&100}}  |1A|Terminal A - RS485|
 +|:::|2A|Terminal B - RS485|
 +|:::|3A|USER PORT common|
 +|:::|4A|USER PORT common|
 +|:::|5A|Terminal TX - RS232|
 +|:::|6A|PE - Ground.|
 +|:::|1B|Terminal RX - RS422|
 +|:::|2B|Terminal RX N - RS422|
 +|:::|3B|Terminal RX - RS422|
 +|:::|4B|Terminal TX N - RS422|
 +|:::|5B|Terminal RX - RS232|
 +|:::|6B|PE - Ground.|
 +
 +==Setup of USER PORT electric standard==
 +^  SW2  ^Num.\\ Dip^Name\\ DIP^Setting\\ of DIP^^^Function^
 +|{{dip-switch:dip-6.png?nolink&100}}|  1  |  JP2  |  ON  |  X[(X = setting not significant)]  |  X[(#1)]  |Termination RS485|
 +|:::|  2  |  JP3  |  ON  |  X[(#1)]  |  X[(#1)]  |Polarisation RS485|
 +|:::|  3  |  JP1  |  ON  |  X[(#1)]  |  X[(#1)]  |:::|
 +|:::|  4  |    |  OFF  |  ON  |  OFF  |Selection of USER PORT electric standard|
 +|:::|  5  |    |  ON  |  OFF  |  OFF  |:::|
 +|:::|  6  |    |  OFF  |  OFF  |  ON  |:::|
 +|:::|    |    |  **RS485**  |  **RS422**  |  **RS232[(the USER PORT can be used as PROG PORT with RS232 electric standard, setting ON in DIP-8 of [[#Selettore baud-rate CANbus|SW1]] and OFF in DIP-6 of [[#Settaggio standard elettrico USER PORT|SW2]])]**  | |
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +==== CN4 - AUX2 RS485 PORT ====
 +|  {{:connettori:cnn_3fv_p3.5_03.jpg?nolink&75}}  |1|0 Volt - RS485 serial common|
 +|:::|2|Terminal RS485 B|
 +|:::|3|Terminal RS485 A|
 +
 +==Setup of AUX2 PORT polarisation and termination resistances==
 +^  SW4  ^Num.\\ Dip^Name\\ Dip^Setting\\ of DIP^Function^
 +|  {{dip-switch:DIP-4.jpg?nolink&80}}  |  1  |  JP3  |  ON  |Polarisation [[#RS485]]|
 +|:::|  2  |  JP2  |  ON  |Termination [[#RS485]]|
 +|:::|  3  |  JP1  |  ON  |Polarisation [[#RS485]]|
 +|:::|  4  | |  X[(X = setting not significant)]  |None|
 +
 +~~REFNOTES~~
 +
 +==== CN5 - CAN PORT ====
 +
 +|  {{:connettori:cnn_3fv_p3.5_03.jpg?nolink&75}}  |1|0 Volt - CAN common|
 +|:::|2|Terminal CAN L|
 +|:::|3|Terminal CAN H|
 +
 +== Setup of CAN1 PORT Termination resistances ==
 +
 +^  SW5  ^Num.\\ Dip^Name\\ Dip^Setting\\ of DIP^Function^
 +|  {{dip-switch:dip-4.jpg?nolink&80}}  |  1  |  JP1  |  ON  |Termination [[#CAN BUS|CAN1]]|
 +|:::|  2  |  JP2  |  ON  |:::|
 +|:::|  3  |  -  |  -  |Not used|
 +|:::|  4  |  -  |  -  |:::|
 +
 +<WRAP center round important 80%>
 +  * If the termination of CAN1 port is activated, both relative DIP JP1 and JP2 must be activated.
 +</WRAP>
 +
 +
 +==== ETHERNET PORT ====
 +
 +^ETHERNET PORT^Description^
 +|  {{connettori:cnn_ethernet_01.png?nolink&70}}  |Connector RJ45.\\ \\ LED:\\  * LINK: green led = cable connected (led on indicates that the cable is connected to both ends)\\  * DATA: yellow led = data transmission (flashing led indicates data transmission between the devices connected)|
 +
 +
 +==== MMC/SD ====
 +
 +{{connettori:connettore_mmc.png?nolink&600}} Connector to insert Memory card (marked by an arrow)
 +
 +<html><pagebreak /></html>
 +
 +==== CN7 - 1 counter (PP, LD) - MMB axis ====
 +
 +^Connector^Pin^ID^Description^^  Address  ^|
 +|  {{:connettori:cnn_2x7f_p3.5_01.png?nolink&100}}  |1A| |Internal bridge - 1A to 1B|| ||
 +|:::|2A|PHA1|A phase counter 1|  PNP  \\  Push-Pull [(:\\  PNP/Push-Pull type count configuration:\\ - Terminal 5B: connect to terminal 5A\\ - Terminal 6B: connect to terminal 6A\\ - Terminal 7B: connect to terminal 7A)]  |3.INP17|3.CNT01|
 +|:::|3A|PHB1|B phase counter 1|:::|3.INP18|:::|
 +|:::|4A|Z1|Z phase counter 1|:::|  1.INT01  ||
 +|:::|5A|0V|Common for count inputs|| ||
 +|:::|6A|0V|:::||:::||
 +|:::|7A|0V|:::||:::||
 +|:::|1B| |Internal bridge - 1A to 1B|| ||
 +|:::|2B|PHA1+|+ PHA counter 1|  Line Driver  |3.INP17|3.CNT01|
 +|:::|3B|PHB1+|+ PHB counter 1|:::|3.INP18|:::|
 +|:::|4B|Z1+|+ Z counter 1|:::|  1.INT01  ||
 +|:::|5B|PHAN1|- PHA counter 1|:::| ||
 +|:::|6B|PHBN1|- PHB counter 1|:::|:::||
 +|:::|7B|ZN1|- Z counter 1|:::|:::||
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +==== CN8 - 1 counter (PP, LD) - MMC axis ====
 +^Connettore^Pin^ID^Description^^  Address  ^|
 +|  {{:connettori:cnn_2x7f_p3.5_01.png?nolink&100}}  |1A| |Internal bridge - 1A to 1B|| ||
 +|:::|2A|PHA2|A phase counter 2|  PNP  \\  Push-Pull [(:\\ PNP/Push-Pull type count configuration:\\ - Terminal 5B: connect to terminal 5A\\ - Terminal 6B: connect to terminal 6A\\ - Terminal 7B: connect to terminal 7A)]  |3.INP19|3.CNT02|
 +|:::|3A|PHB2|B phase counter 2|:::|3.INP20|:::|
 +|:::|4A|Z2|Z phase counter 2|:::|  1.INT02  ||
 +|:::|5A|0V|Common for count inputs|| ||
 +|:::|6A|0V|:::||:::||
 +|:::|7A|0V|:::||:::||
 +|:::|1B| |Internal bridge - 1A to 1B|| ||
 +|:::|2B|PHA2+|+ PHA counter 2|  Line Driver  |3.INP19|3.CNT02|
 +|:::|3B|PHB2+|+ PHB counter 2|:::|3.INP20|:::|
 +|:::|4B|Z2+|+ Z counter 2|:::|  1.INT02  ||
 +|:::|5B|PHAN2|- PHA counter 2|:::| ||
 +|:::|6B|PHBN2|- PHB counter 2|:::|:::||
 +|:::|7B|ZN2|- Z counter 2|:::|:::||
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +==== CN9 - 1 counter (PP, LD) - MCB axis ====
 +^Connettore^Pin^ID^Description^^  Address  ^|
 +|  {{:connettori:cnn_2x7f_p3.5_01.png?nolink&100}}  |1A| |Internal bridge - 1A to 1B|| ||
 +|:::|2A|PHA3|A phase counter 3|  PNP  \\  Push-Pull [(:\\ PNP/Push-Pull type count configuration:\\ - Terminal 5B: connect to terminal 5A\\ - Terminal 6B: connect to terminal 6A\\ - Terminal 7B: connect to terminal 7A)]  |3.INP21|3.CNT03|
 +|:::|3A|PHB3|B phase counter 3|:::|3.INP22|:::|
 +|:::|4A|Z3|Z phase counter 3|:::|  1.INT03  ||
 +|:::|5A|0V|Common for count inputs|| ||
 +|:::|6A|0V|:::||:::||
 +|:::|7A|0V|:::||:::||
 +|:::|1B| |Internal bridge - 1A to 1B|| ||
 +|:::|2B|PHA3+|+ PHA counter 3|  Line Driver  |3.INP21|3.CNT03|
 +|:::|3B|PHB3+|+ PHB counter 3|:::|3.INP22|:::|
 +|:::|4B|Z3+|+ Z counter 3|:::|  1.INT03  ||
 +|:::|5B|PHAN3|- PHA counter 3|:::| ||
 +|:::|6B|PHBN3|- PHB counter 3|:::|:::||
 +|:::|7B|ZN3|- Z counter 3|:::|:::||
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +==== CN10 - 1 counter (PP, LD) - MT axis ====
 +^Connector^Pin^ID^Description^^  Address  ^|
 +|  {{:connettori:cnn_2x7f_p3.5_01.png?nolink&100}}  |1A| |Internal bridge - 1A to 1B|| ||
 +|:::|2A|PHA4|A phase counter 4|  PNP  \\  Push-Pull [(:\\  PNP/Push-Pull type count configuration:\\ - Terminal 5B: connect to terminal 5A\\ - Terminal 6B: connect to terminal 6A\\ - Terminal 7B: connect to terminal 7A)]  |3.INP23|3.CNT04|
 +|:::|3A|PHB4|B phase counter 4|:::|3.INP24|:::|
 +|:::|4A|Z4|Z phase counter 4|:::|  1.INT04  ||
 +|:::|5A|0V|Common for count inputs|| ||
 +|:::|6A|0V|:::||:::||
 +|:::|7A|0V|:::||:::||
 +|:::|1B| |Internal bridge - 1A to 1B|| ||
 +|:::|2B|PHA4+|+ PHA counter 4|  Line Driver  |3.INP23|3.CNT04|
 +|:::|3B|PHB4+|+ PHB counter 4|:::|3.INP24|:::|
 +|:::|4B|Z4+|+ Z counter 4|:::|  1.INT04  ||
 +|:::|5B|PHAN4|- PHA counter 4|:::| ||
 +|:::|6B|PHBN4|- PHB counter 4|:::|:::||
 +|:::|7B|ZN4|- Z counter 4|:::|:::||
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>
 +
 +==== CN11 - 8 standard digital inputs + 1 rapid input (PNP) ====
 +^Connector^Pin^ID^Description^Address|
 +|  {{:connettori:cnn_12fv_p3.5_02.png?nolink&75}}  |1|-|//Free//| |
 +|:::|2|-|//Free//| |
 +|:::|3|0V|Vout (0 V) - Common for digital inputs I1÷I8| |
 +|:::|4|I1|Fault MMB driver|3.INP01|
 +|:::|5|I2|Fault MMC driver|3.INP02|
 +|:::|6|I3|Fault MCB driver|3.INP03|
 +|:::|7|I4|Start (1)/Stop (0) sinchronism|3.INP04|
 +|:::|8|I5|Emergency|3.INP05|
 +|:::|9|I6|Enabling Switch Zero MMB axis|3.INP06|
 +|:::|10|I7|Enabling Switch Zero MMC axis|3.INP07|
 +|:::|11|I8|Enabling Switch Zero MCB axis|3.INP08|
 +|:::|12|0V|Vout (0 V) - Common for digital inputs I1÷I8| |
 +
 +==== CN12 - 8 standard digital inputs + 1 rapid input (PNP) ====
 +^Connector^Pin^ID^Description^Address|
 +|  {{:connettori:cnn_12fv_p3.5_02.png?nolink&75}}  |1|-|//Free//| |
 +|:::|2|-|//Free//| |
 +|:::|3|0V|Vout (0 V) - Common for digital inputs I9÷I16| |
 +|:::|4|I9|Manual (0) / Automatic (1) selector|3.INP09|
 +|:::|5|I10|Start Homing|3.INP10|
 +|:::|6|I11|Jog forward selected axis|3.INP11|
 +|:::|7|I12|Jog backward selected axis|3.INP12|
 +|:::|8|I13|MMB1 axis selection for jog movements|3.INP13|
 +|:::|9|I14|MMB2 axis selection for jog movements|3.INP14|
 +|:::|10|I15|MCB axis selection for jog movements|3.INP15|
 +|:::|11|I16|//Free//|3.INP16|
 +|:::|12|0V|Vout (0 V) - Common for digital inputs I9÷I16| |
 +
 +<html><pagebreak /></html>
 +
 +==== CN15 - 8 protected digital outputs (24V - 0,5 A) ====
 +^Connector^Pin^ID^Description^Address|
 +|  {{:connettori:cnn_11fv_p3.5_02.png?nolink&75}}  |1|V+|Outputs power in (12-28Vdc)| |
 +|:::|2|O1|Reset MMB driver|3.OUT01|
 +|:::|3|O2|Reset MMC driver|3.OUT02|
 +|:::|4|-|n.c.| |
 +|:::|5|O3|Reset MCB driver|3.OUT03|
 +|:::|6|O4|Cycle on signal|3.OUT04|
 +|:::|7|0V|Outputs power in (12-28Vdc)| |
 +|:::|8|O5|Enable MMB driver|3.OUT05|
 +|:::|9|O6|Enable MMC driver|3.OUT06|
 +|:::|10|O7|Enable MCB driver|3.OUT07|
 +|:::|11|O8|Emergency Normally closed|3.OUT08|
 +
 +
 +==== CN16 - 8 protected digital outputs (24V - 0,5 A) ====
 +^Connector^Pin^ID^Description^Address|
 +|  {{:connettori:cnn_11fv_p3.5_02.png?nolink&75}}  |1|V+|Outputs power in (12-28Vdc)| |
 +|:::|2|O9|Emergency state lamp|3.OUT09|
 +|:::|3|O10|Manual state lamp|3.OUT10|
 +|:::|4|-|n.c.| |
 +|:::|5|O11|Homing done - machine ready|3.OUT11|
 +|:::|6|O12|//Free//|3.OUT12|
 +|:::|7|0V|Outputs power in (12-28Vdc)| |
 +|:::|8|O13|//Free//|3.OUT13|
 +|:::|9|O14|//Free//r|3.OUT14|
 +|:::|10|O15|//Free//|3.OUT15|
 +|:::|11|O16|//Free//|3.OUT16|
 +
 +<html><pagebreak /></html>
 +
 +==== CN17 - 4 analog outputs ====
 +^Connector^Pin^ID^Description^Address|
 +|  {{:connettori:cnn_6fv_p3.5_02.png?nolink&75}}  |1|GA01|Common for analog outputs A01÷A02| |
 +|:::|2|AO1|MMB axis speed control ±10Vdc|3.AN01|
 +|:::|3|AO2|MMC axis speed control ±10Vdc|3.AN02|
 +|:::|4|GA02|Common for analog outputs A03÷A04| |
 +|:::|5|AO3|MCB axis speed control ±10Vdc|3.AN03|
 +|:::|6|AO4|//Free//|3.AN04|
 +
 +==== CN18 - 2 analog inputs, 12bit potentiometric, voltmetric and amperometric ====
 +All inputs are __//**Free**//__
 +
 +<html><pagebreak /></html>
 +
 +===== A1-HMI-QC050 =====
 +
 +==== CN1- Power supply (Slot supply) ====
 +^Power supplies available^24 Vdc^24 Vac^
 +^Voltage range|22 ÷ 27 Vdc|+/-15%|
 +^Max. absorption|30W|35VA|
 +^Frequency| |50/60Hz|
 +
 +|  {{:connettori:cnn_3fv_p5_01.png?nolink}}  |1|AC power phase/ DC power positive|
 +|:::|2|Gnd-PE (signals)|
 +|:::|3|AC power phase/ DC power 0V|
 +
 +<html><pagebreak /></html>
 +
 +==== CN2 - PORTA USER. Multistandard serial RS232-RS422-RS485 (isolated) ====
 +Serial port used to connect hmi with C1-R11-FE30 (RS422).
 +
 +|  {{:connettori:cnn_6x2fv_p3.5_01.png?nolink&100}}  |1A|Terminal A - RS485|
 +|:::|2A|Terminal B - RS485|
 +|:::|3A|USER PORT common|
 +|:::|4A|USER PORT common|
 +|:::|5A|Terminal TX - RS232|
 +|:::|6A|PE - Ground.|
 +|:::|1B|Terminal RX - RS422|
 +|:::|2B|Terminal RX N - RS422|
 +|:::|3B|Terminal RX - RS422|
 +|:::|4B|Terminal TX N - RS422|
 +|:::|5B|Terminal RX - RS232|
 +|:::|6B|PE - Ground.|
 +
 +==Setup of USER PORT electric standard==
 +^  SW2  ^Num.\\ Dip^Name\\ DIP^Setting\\ of DIP^^^Function^
 +|{{dip-switch:dip-6.png?nolink&100}}|  1  |  JP2  |  ON  |  X[(X = setting not significant)]  |  X[(#1)]  |Termination RS485|
 +|:::|  2  |  JP3  |  ON  |  X[(#1)]  |  X[(#1)]  |Polarisation RS485|
 +|:::|  3  |  JP1  |  ON  |  X[(#1)]  |  X[(#1)]  |:::|
 +|:::|  4  |    |  OFF  |  ON  |  OFF  |Selection of USER PORT electric standard|
 +|:::|  5  |    |  ON  |  OFF  |  OFF  |:::|
 +|:::|  6  |    |  OFF  |  OFF  |  ON  |:::|
 +|:::|    |    |  **RS485**  |  **RS422**  |  **RS232[(the USER PORT can be used as PROG PORT with RS232 electric standard, setting ON in DIP-8 of [[#Selettore baud-rate CANbus|SW1]] and OFF in DIP-6 of [[#Settaggio standard elettrico USER PORT|SW2]])]**  | |
 +
 +~~REFNOTES~~
 +
 +<html><pagebreak /></html>