en:software:devices:qmos

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		 Previous revision
en:software:devices:qmos [2016/12/27 15:04] – created qem103en:software:devices:qmos [2019/08/29 17:01] (current) – external edit 127.0.0.1
Line 1: Line 1:
 +====== DEVICE QMOS ======
 +
 +====== - Parameters list ======
 +
 +===== - osmode =====
 +
 +{{template>en:lib:tpl:tpl-s-tapardev-010
 +|shortdescr=Operative system state|
 +|dim=Byte|
 +|default= - |
 +|accesstype=Read |
 +|um=-|
 +|id=-|
 +|range=0÷5|
 +|wrcond= - |
 +|longdescr=Reflects the operative system state. Where: 
 +
 +0 = OSINI (Initialization)\\
 +1 = OSRES (Reset)\\
 +2 = OSRDY (Ready)\\
 +3 = OSRUN (Run)\\
 +4 = OSSTP (Stop)\\
 +5 = OSERR (Error)\\}}
 +---- 
 +<html><pagebreak /></html>
 +
 +
 +===== - oserr =====
 +
 +{{template>en:lib:tpl:tpl-s-tapardev-010
 +|shortdescr=Operative system error code|
 +|dim=Byte|
 +|default= - |
 +|accesstype=Read |
 +|um=-|
 +|id=-|
 +|range=0÷10|
 +|wrcond= - |
 +|longdescr=Reflects the operative system error code. Where: 
 +
 +1 = OSBUSER (Bus Error)\\
 +2 = OSCKSER (CheckSum Error)\\
 +3 = OSIDXOB (Index Out of Bound)\\
 +4 = OSPRGOR (Program Over Range)\\
 +5 = OSSTPOR (Step Over Range)\\
 +6 = OSDVZER (Division By Zero)\\
 +7 = OSSTXER (Syntax Error)\\
 +8 = OSWDGER (WatchDog Error)\\
 +9 = OSSTKER (Stack Error)\\
 +10 = OSFLHER (Flash error)\\}}
 +---- 
 +<html><pagebreak /></html>
 +
 +
 +===== - osflags =====
 +
 +{{template>en:lib:tpl:tpl-s-tapardev-010
 +|shortdescr=Operative system flags|
 +|dim=Byte|
 +|default= - |
 +|accesstype=Read |
 +|um=-|
 +|id=-|
 +|range= - |
 +|wrcond= - |
 +|longdescr=Reflects the operative system internal flags. Where: 
 +
 +bit 0 (LSB) TSKWDER (Task Watchdog Error)\\
 +bit 1 BATTERY (wrong battery)\\
 +bit 2 BKDIS (backup disabled)\\
 +bit 3 TTASKLOST (timed task list)\\
 +bit 4 BKNEW (new backup procedure)\\
 +bit 5 BKPRESENT (backup present)\\
 +bit 6 BKVALID (backup valid)\\
 +bit 7 (MSB) empty\\}}
 +---- 
 +<html><pagebreak /></html>
 +
 +^Name^D^R^A^Description^
 +|systimeh|L|-|R|Shown the system timer LONG_H that has resolution 1 msec.|
 +|systimel|L|-|R|Shown the system timer LONG_L that has resolution 1 msec.|
 +|taskmedtime|L|-|R|Indicates the average time of your program's execution (tenths of a msec.)|
 +|taskmaxtime|L|-|R|Indicates the maximum execution time of the program (tenths of a msec.)|
 +|taskmintime|L|-|R|Indicates the minimum execution time of the program (tenths of a msec.)|
 +|sizeapp|L|-|R|Indicates the size of the QCL application (bytes) stored in flash|
 +|sizeret|L|-|R|Indicates the size of the retentive memory used (bytes)|
 +|memfree|L|-|R|Indicates the amount of volatile memory (bytes) still available|
 +|sys001\\ ...\\ sys016|L|-|R-W|System variables|
 +|frwname01\\ ...\\ frwname09|B|-|R|Bootloader: firmware identification string|
 +|frwversion|B|-|R|Bootloader: firmware version|
 +|frwmajrel|B|-|R|Bootloader: firmware major release|
 +|frwminrel|B|-|R|Bootloader: firmware minor release|
 +|frwhwid|L|-|R|Bootloader: firmware hardware ID|
 +|frwcks|L|-|R|Bootloader: firmware checksum|
 +|frwuvalue01\\ ...\\ frwuvalue10|L|-|R|Bootloader: user value|
 +|fwxversion|B|-|R|Support external controller firmware version|
 +|fwxmajrel|B|-|R|External controller firmware support major release|
 +|fwxminrel|B|-|R|External controller firmware support minor release|
 +|temperature|B|-|R|Internal temperature expressed in °C|
 +|par01|L|-|R-W|Parameter for future use|
 +|par02|L|-|R-W|Parameter for future use|
 +|par03|L|-|R-W|Parameter for future use|
 +|par04|L|-|R-W|Parameter for future use|
 +|par05|L|-|R-W|Parameter for future use|
 +
 +
 +===== - States table =====
 +
 +^Name^D^R^A^Descriptionm^
 +|st_backup|F|-|-|Indicates that there is a valid backup|
 +|st_01|F|-|-|State for future use|
 +|st_02|F|-|-|State for future use|
 +|st_03|F|-|-|State for future use|
 +|st_04|F|-|-|State for future use|
 +|st_05|F|-|-|State for future use|
 +
 +
 +===== - Commands table =====
 +
 +^Name^D^R^A^Description^
 +|RESTART|F|-|W|Restart of the system.|
 +|BACKUP|F|-|W|Start the backup procedure (if present)|
 +|RESTORE|F|-|W|Start the application restore procedure (if present)|
 +|CMD01|F|-|W|Command for future use|
 +|CMD02|F|-|W|Command for future use|
 +|CMD03|F|-|W|Command for future use|
 +|CMD04|F|-|W|Command for future use|
 +|CMD05|F|-|W|Command for future use|
 +