| Both sides previous revision Previous revision Next revision | Previous revision |
| en:strumenti:qmoveplus:c1r44:p1r44f-001:mdo_p1r44f-009 [2022/12/14 13:57] – [Features implemented in the current proposal] qem215 | en:strumenti:qmoveplus:c1r44:p1r44f-001:mdo_p1r44f-009 [2022/12/23 15:49] (current) – [Belt] qem215 |
|---|
| ^ Editor: | Andrea Zarantonello ||| | ^ Editor: | Andrea Zarantonello ||| |
| ^ Approver | Giuliano Tognon ||| | ^ Approver | Giuliano Tognon ||| |
| ^ Link: | http://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/c1r44/p1r44f-001/mdo_p1r44f-009 ||| | ^ Link: | https://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/c1r44/p1r44f-001/mdo_p1r44f-009 ||| |
| ^ Language: | English ||| | ^ Language: | English ||| |
| | |||| | | |||| |
| | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_motor_120x60_off.png?100&nolink}} | Access to the engine test page. | | | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_motor_120x60_off.png?100&nolink}} | Access to the engine test page. | |
| | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_page.png?100&nolink}} | Access to the belt speed setting page | | | {{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_page.png?100&nolink}} | Access to the belt speed setting page | |
| | | {{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_disable_page_button.png?100&nolink}} | Access to enable/disable heads page | |
| | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_belt_60x60_off.png?50&nolink}} | Forcing the movement of the conveyor belt and the conveyor rollers (only in manual mode). | | | {{:strumenti:qmoveplus:c1r11:mdu_p1r11fb30-001Q:buttons:butt_belt_60x60_off.png?50&nolink}} | Forcing the movement of the conveyor belt and the conveyor rollers (only in manual mode). | |
| |
| | Air pressure | Input from pressure switch (I05) deactivated or insufficient air pressure | Check pressure switch or connections | | | Air pressure | Input from pressure switch (I05) deactivated or insufficient air pressure | Check pressure switch or connections | |
| | Thermal overload | Input (I01) from one of the thermal switches off | Check switches and wiring | | | Thermal overload | Input (I01) from one of the thermal switches off | Check switches and wiring | |
| | Bridge inverter KO | Bridge inverter malfunction (I02 Off) | Check inverter or wiring | | | Bridge inverter fault | Bridge inverter malfunction (I02 Off) | Check inverter or wiring | |
| | Belt inverter KO | Conveyor belt inverter Malfunction (I03 Off) | Check Inverter or Wiring | | | Belt inverter fault | Conveyor belt inverter Malfunction (I03 Off) | Check Inverter or Wiring | |
| | Roller inverter KO | Roller conveyor inverter malfunction (I04 Off) | Check inverter or wiring | | | Roller inverter fault | Roller conveyor inverter malfunction (I04 Off) | Check inverter or wiring | |
| | Emergency button pressed | Emergency button (I13) pressed | Unlock button or check wiring | | | Emergency button pressed | Emergency button (I13) pressed | Unlock button or check wiring | |
| | CANBUS communication error (RMC3M-DD) | Error in communication with node 1 of the CANOPEN network. Node 1 is represented by the RMC3M-DD I / O module which manages the outputs relating to the heads. | Remove and restore power to the system. If this is not enough, check the bus wiring. | | | CANBUS communication error (RMC3M-DD) | Error in communication with node 1 of the CANOPEN network. Node 1 is represented by the RMC3M-DD I / O module which manages the outputs relating to the heads. | Remove and restore power to the system. If this is not enough, check the bus wiring. | |
| |
| Look in the [[en/strumenti:qmoveplus:c1r44:p1r44f-001:mmf_p1r44f-009|start up manual]] how to best perform the procedures. | Look in the [[en/strumenti:qmoveplus:c1r44:p1r44f-001:mmf_p1r44f-009|start up manual]] how to best perform the procedures. |
| <html><pagebreak /></html> | |
| | The button {{:strumenti:qmoveplus:c1r44:p1r44f-001:offset_button.png?nolink&100|}} open the page "Offset tools": |
| | |
| | {{:strumenti:qmoveplus:c1r44:p1r44f-001:offset_teste.png?nolink&500|}} |
| | |
| | In this page is possible to set a horizontal offset for every single head.\\ The button =0 reset all the offset values \\ The button "progression" associate to every head the value "progression of" + offset of the head before. |
| ==== Orthogonal correction==== | ==== Orthogonal correction==== |
| Look image [[#Functioning| general view machine]] | Look image [[#Functioning| general view machine]] |
| |
| In this page it is possible to set the speed of the conveyor belt. Max and min values are setted in generic parameters (PG 36 PG 37). | In this page it is possible to set the speed of the conveyor belt. Max and min values are setted in generic parameters (PG 36 PG 37). |
| | If the machine is in **MANUAL** state:\\ press button {{:strumenti:qmoveplus:c1r44:p1r44f-001:pulsante_rulliere.png?nolink&50|}} to activate O3: ROLLERS RUN, \\ press button{{:en:strumenti:qmoveplus:c1r44:p1r44f-001:belt_page.png?nolink&90|}} to activate O2 "BELT RUN" |
| | <html><pagebreak /></html> |
| | |
| | ===== Enable/Disable Tools ===== |
| | {{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_disable_page_button.png?100&nolink}} -> {{:strumenti:qmoveplus:c1r44:p1r44f-001:enable_head_page.png?nolink&400|}} |
| | |
| | In this page it's possible to enable or disable the tools.\\ Led on (yellow) = tool enabled\\ Led off(grey) = tool disabled |
| |
| <html><pagebreak /></html> | <html><pagebreak /></html> |