P1P51FE30 - 001 : Wiring connections
![]() |
|||
Document | mce_p1p51fe30-001 | ||
---|---|---|---|
Descrizion | Electric connections manual for application P1P51FE30-001 | ||
Drawn up | Michele Sandri | ||
Approved | Gabriele Bazzi | ||
Link | http://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/j1p51/p1p51fe30-001/mce_p1p51fe30-001 | ||
Language | English | ||
Document Release | Description | Notes | Date |
01 | New manual | 10/06/2015 |
All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation. QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information in this document can be changed without notice. QEM shall not be held liable for any error or omission in this document. QEM® is a registered trademark.
1. Hardware
1.1 Operator Panel
J1-P51-FE30/TP00 | |
---|---|
![]() |
|
![]() |
|
![]() | MIMJ1P51Fx:Installation and Maintenance Manual |
2. I/O Resources
2.1 Digital Inputs
-
NO = Normally Opened
-
NC = Normally Closed
-
PR = Programmable
-
I = Impulsive
-
C = Continuous
NAME | DESCRIPTION | LOGIC | TERMINAL | HARDWARE | |||
---|---|---|---|---|---|---|---|
I01 | Jog button forward Z [P] | NO | I | ![]() | CN11.1 | J1-P51 | |
∩ | Connect to terminal CN11.3 | CN11.2 | |||||
0V | Common for digital inputs | CN11.3 | |||||
I1 | FC Y maximum | NC | C | CN11.4 | |||
I2 | FC Y minimum | NC | C | CN11.5 | |||
I3 | Motor driver disk fault | NC | C | CN11.6 | |||
I4 | Disc motor running | NO | C | CN11.7 | |||
I5 | Disc motor in stop | NO | C | CN11.8 | |||
I6 | Auxiliary OK | NO | C | CN11.9 | |||
I7 | Air disc motor and thermal OK | NO | C | CN11.10 | |||
I8 | Thermal engine oil pump OK | NO | C | CN11.11 | |||
0V | Common for digital inputs | CN11.12 | |||||
I02 | Jog button back Z [P] | NO | I | ![]() | CN12.1 | J1-P51 | |
∩ | Connect to terminal CN12.3 | CN12.2 | |||||
0V | Common for digital inputs | CN12.3 | |||||
I9 | Barrier closed | NO | C | CN12.4 | |||
I10 | Pressure water present | NO | C | CN12.5 | |||
I11 | Desk horizontal position sensor | NO | C | CN12.6 | |||
I12 | Motor Driver X fault | NO | C | CN12.7 | |||
I13 | Motor Driver Y fault | NO | C | CN12.8 | |||
I14 | Motor Driver Y1 fault | NO | C | CN12.9 | |||
I15 | Motor Driver Z fault | NO | C | CN12.10 | |||
I16 | Motor Driver C fault | NO | C | CN12.11 | |||
0V | Common for digital inputs | CN12.12 | |||||
I03 | Button climb tilting bench [P] | NO | I | ![]() | CN13.1 | J1-P51 | |
∩ | Connect to terminal CN13.3 | CN13.2 | |||||
0V | Common for digital inputs | CN13.3 | |||||
I17 | FC X maximum | NC | C | CN13.4 | |||
I18 | FC X minimum | NC | C | CN13.5 | |||
I19 | FC Z Up | NC | C | CN13.6 | |||
I20 | FC Z Down | NC | C | CN13.7 | |||
I21 | FC C maximum | NC | C | CN13.8 | |||
I22 | FC C minimum | NC | C | CN13.9 | |||
I23 | Low oil level | NO | C | CN13.10 | |||
I24 | Micro Homing Y1 axis | NO | C | CN13.11 | |||
0V | Common for digital inputs | CN13.12 | |||||
I04 | Button-down tilting bench [P] | NO | I | ![]() | CN14.1 | J1-P51 | |
∩ | Connect to terminal CN14.3 | CN14.2 | |||||
0V | Common for digital inputs | CN14.3 | |||||
I25 | RESET button automatic cycle [P] | NO | I | CN14.4 | |||
I26 | STOP automatic cycle (HOLD) [P] | NC | I | CN14.5 | |||
I27 | Jog button forward X [P] | NC | I | CN14.6 | |||
I28 | Jog button back X [P] | NC | I | CN14.7 | |||
I29 | Jog button forward Y [P] | NC | I | CN14.8 | |||
I30 | Button jog back Y [P] | NC | I | CN14.9 | |||
I31 | Selector blade speed | NC | C | CN14.10 | |||
I32 | Selector spindle speed | NC | C | CN14.11 | |||
0V | Common for digital inputs | CN14.12 |
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
---|---|---|---|---|
- | Not used | ![]() | CN22.1A | J1-P51 |
PHA1 | Start button [P] | CN22.2A | ||
PHB1 | Reserve | CN22.3A | ||
Z1 | Reserve | CN22.4A | ||
∩ | Connect to terminal 5B | CN22.5A | ||
∩ | Connect to terminal 6B | CN22.6A | ||
0V ∩ | Common for count inputs Connect to terminal 7B | CN22.7A | ||
- | Not used | CN22.1B | ||
- | CN22.2B | |||
- | CN22.3B | |||
- | CN22.4B | |||
∩ | Connect to terminal 5A | CN22.5B | ||
∩ | Connect to terminal 6A | CN22.6B | ||
∩ | Connect to terminal 7A | CN22.7B |
2.2 Digital Outputs
-
I = Impulsive
-
C = Continuous
NAME | DESCRIPTION | LOGIC | TERMINAL | HARDWARE | ||
---|---|---|---|---|---|---|
V+ | Input Supply digital output (+24V) | - | ![]() | CN7.1 | J1-P51 | |
O1 | Enabling spindle | C | CN7.2 | |||
O2 | Activation by-pass safety barriers | C | CN7.3 | |||
V- | not used | CN7.4 | ||||
O3 | Turning oil pump for tilting bench | C | CN7.5 | |||
O4 | Enabling EV water cooling | C | CN7.6 | |||
V- | Common for digital output (0V) | CN7.7 | ||||
O5 | Laser activation | C | CN7.8 | |||
O6 | Machine OK | C | CN7.9 | |||
O7 | Lamp presence alarm | I/C | CN7.10 | |||
O8 | Enabling EV climb bench | C | CN7.11 | |||
V+ | Input Supply digital output (+24V) | - | ![]() | CN8.1 | ||
O9 | Enabling EV descent bench | C | CN8.2 | |||
O10 | Enable drive axis X | C | CN8.3 | |||
V- | not used | CN8.4 | ||||
O11 | Enable drive axis Y | C | CN8.5 | |||
O12 | Enable drive axis Y1 | C | CN8.6 | |||
V- | Common for digital output (0V) | CN8.7 | ||||
O13 | Enable drive axis Z | C | CN8.8 | |||
O14 | Enable drive axis C | C | CN8.9 | |||
O15 | Signaling axis in motion | C | CN8.10 | |||
O16 | Reset driver | I/C | CN8.11 | |||
V+ | Input Supply digital output (+24V) | - | ![]() | CN9.1 | ||
O17 | Selection rotating disk (OFF) or cutter (ON) | I/C | CN9.2 | |||
O18 | Activation lubrication | C | CN9.3 | |||
V- | not used | CN9.4 | ||||
O19 | Lamp automatic cycle stopped [P] | C | CN9.5 | |||
O20 | Lamp disk in motion with cycle stop [P] | I | CN9.6 | |||
V- | Common for digital output (0V) | CN9.7 | ||||
O21 | Lamp automatic cycle in progress [P] | C | CN9.8 | |||
O22 | Bypass safety barriers Active lamp [P] | C | CN9.9 | |||
O23 | Lamp (or beep) alarm in progress [P] | I | CN9.10 | |||
O24 | Auxiliary lamp lit and ready CN [P] | C | CN9.11 | |||
V+ | Input Supply digital output (+24V) | - | ![]() | CN10.1 | ||
O25 | reserve | CN10.2 | ||||
O26 | reserve | CN10.3 | ||||
V- | not used | CN10.4 | ||||
O27 | reserve | CN10.5 | ||||
O28 | reserve | CN10.6 | ||||
V- | Common for digital output (0V) | CN10.7 | ||||
O29 | reserve | CN10.8 | ||||
O30 | reserve | CN10.9 | ||||
O31 | reserve | CN10.10 | ||||
O32 | reserve | CN10.11 |
2.3 Two-way Encoder Count Inputs
Axis X (Line Driver) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN15.1A | J1-P51 |
- | CN15.2A | |||
- | CN15.3A | |||
- | CN15.4A | |||
- | CN15.5A | |||
- | CN15.6A | |||
0V | Common for count inputs | CN15.7A | ||
- | Not used | CN15.1B | ||
PHA1+ | + PHA | CN15.2B | ||
PHB1+ | + PHB | CN15.3B | ||
Z1+ | + Z | CN15.4B | ||
PHA1- | - PHA | CN15.5B | ||
PHB1- | - PHB | CN15.6B | ||
Z1- | - Z | CN15.7B |
Axis Y (Line Driver) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN16.1A | J1-P51 |
- | CN16.2A | |||
- | CN16.3A | |||
- | CN16.4A | |||
- | CN16.5A | |||
- | CN16.6A | |||
0V | Common for count inputs | CN16.7A | ||
- | Not used | CN16.1B | ||
PHA2+ | + PHA | CN16.2B | ||
PHB2+ | + PHB | CN16.3B | ||
Z2+ | + Z | CN16.4B | ||
PHA2- | - PHA | CN16.5B | ||
PHB2- | - PHB | CN16.6B | ||
Z2- | - Z | CN16.7B |
Axis Z (Line Driver) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN17.1A | J1-P51 |
- | CN17.2A | |||
- | CN17.3A | |||
- | CN17.4A | |||
- | CN17.5A | |||
- | CN17.6A | |||
0V | Common for count inputs | CN17.7A | ||
- | Not used | CN17.1B | ||
PHA3+ | + PHA | CN17.2B | ||
PHB3+ | + PHB | CN17.3B | ||
Z3+ | + Z | CN17.4B | ||
PHA3- | - PHA | CN17.5B | ||
PHB3- | - PHB | CN17.6B | ||
Z3- | - Z | CN17.7B |
Axis Y1 (Line Driver) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN18.1A | J1-P51 |
- | CN18.2A | |||
- | CN18.3A | |||
- | CN18.4A | |||
- | CN18.5A | |||
- | CN18.6A | |||
0V | Common for count inputs | CN18.7A | ||
- | Not used | CN18.1B | ||
PHA4+ | + PHA | CN18.2B | ||
PHB4+ | + PHB | CN18.3B | ||
Z4+ | + Z | CN18.4B | ||
PHA4- | - PHA | CN18.5B | ||
PHB4- | - PHB | CN18.6B | ||
Z4- | - Z | CN18.7B |
Axis C (Line Driver) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN19.1A | J1-P51 |
- | CN19.2A | |||
- | CN19.3A | |||
- | CN19.4A | |||
- | CN19.5A | |||
- | CN19.6A | |||
0V | Common for count inputs | CN19.7A | ||
- | Not used | CN19.1B | ||
PHA5+ | + PHA | CN19.2B | ||
PHB5+ | + PHB | CN19.3B | ||
Z5+ | + Z | CN19.4B | ||
PHA5- | - PHA | CN19.5B | ||
PHB5- | - PHB | CN19.6B | ||
Z5- | - Z | CN19.7B |
Axis A (Push-Pull) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN20.1A | J1-P51 |
PHA6 | Phase A | CN20.2A | ||
PHB6 | Phase B | CN20.3A | ||
Z6 | Z | CN20.4A | ||
∩ | Connect to terminal 5B | CN20.5A | ||
∩ | Connect to terminal 6B | CN20.6A | ||
0V ∩ | Common for count inputs Connect to terminal 7B | CN20.7A | ||
- | Not used | CN20.1B | ||
- | CN20.2B | |||
- | CN20.3B | |||
- | CN20.4B | |||
∩ | Connect to terminal 5A | CN20.5B | ||
∩ | Connect to terminal 6A | CN20.6B | ||
∩ | Connect to terminal 7A | CN20.7B |
Axis Flyer (Push-Pull) |
||||
---|---|---|---|---|
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
- | Not used | ![]() | CN21.1A | J1-P51 |
PHA7 | Phase A | CN21.2A | ||
PHB7 | Phase B | CN21.3A | ||
Z7 | Z | CN21.4A | ||
∩ | Connect to terminal 5B | CN21.5A | ||
∩ | Connect to terminal 6B | CN21.6A | ||
0V ∩ | Common for count inputs Connect to terminal 7B | CN21.7A | ||
- | Not used | CN21.1B | ||
- | CN21.2B | |||
- | CN21.3B | |||
- | CN21.4B | |||
∩ | Connect to terminal 5A | CN21.5B | ||
∩ | Connect to terminal 6A | CN21.6B | ||
∩ | Connect to terminal 7A | CN21.7B |
2.4 Analog Inputs
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
---|---|---|---|---|
GAI | Common for analog inputs | ![]() | CN28.1 | J1-P51 |
AI1 | Setting cutting speed interpolation (potentiometer) | CN28.2 | ||
SEL1V | Not used | CN28.3 | ||
SEL1C | Not used | CN28.4 | ||
GAI | Common for analog inputs | CN28.5 | ||
AI2 | Amperage reading of the spindle motor (0-10V) | CN28.6 | ||
SEL2V ∩ | Connect to GAI (terminal CN28.5) | CN28.7 | ||
SEL2C | Not used | CN28.8 | ||
VRef | Reference Voltage | CN28.9 | ||
GAI | Common for analog inputs | ![]() | CN29.1 | |
AI3 | Setting speed in the cutting direction (potentiometer) | CN29.2 | ||
SEL3V | Not used | CN29.3 | ||
SEL3C | Not used | CN29.4 | ||
GAI | Common for analog inputs | CN29.5 | ||
AI4 | Setting speed in the opposite direction to the cutting (potentiometer) | CN29.6 | ||
SEL4V | Not used | CN29.7 | ||
SEL4C | Not used | CN29.8 | ||
VRef | Reference Voltage | CN29.9 |
2.5 Analog Outputs
NAME | DESCRIPTION | TERMINAL | HARDWARE | |
---|---|---|---|---|
GAO | Common for analog outupts | ![]() | CN26.1 | J1-P51 |
AO1 | Axis X speed control ±10Vdc | CN26.2 | ||
AO2 | Axis Y speed control ±10Vdc | CN26.3 | ||
GAO | Common for analog outupts | CN26.4 | ||
AO3 | Axis Z speed control ±10Vdc | CN26.5 | ||
AO4 | Axis Y1 speed control ±10Vdc | CN26.6 | ||
GAO | Common for analog outupts | ![]() | CN27.1 | |
AO5 | Axis C speed control ±10Vdc | CN27.2 | ||
AO6 | Not used | CN27.3 | ||
GAO | Common for analog outupts | CN27.4 | ||
AO7 | Reference (0-10V) for spindle speed | CN27.5 | ||
AO8 | Not used | CN27.6 |